Kit Number | Grab Strap | Kit Number | Grab Strap | |
---|---|---|---|---|
51297-06 | 51705-06 | 51417-08 | 51705-06 | |
51298-06 | 51705-06 | 51420-08 | 51705-06 | |
51299-06 | 51705-06 | 51423-08 | 51705-06 | |
51301-06 | 51705-06 | 51424-08 | 51705-06 | |
51305-07 | 51705-06 | 51425-08 | 51705-06 | |
51306-07 | 51333-07 | 51439-08 | 51705-06 | |
51353-06 | 51705-06 | 51447-08 | 51705-06 | |
51359-06 | 51705-06 | 51452-08 | 51705-06 | |
51364-07 | 51705-06 | 52046-06 | None | |
51366-07 | 51705-06 | 52047-06 | None | |
51369-06 | 51705-06 | 52048-06 | 51705-06 | |
51375-06 | None | 52051-06 | 51705-06 | |
51381-06 | 51705-06 | 51621-09 | 51705-06 | |
51626-09 | 51705-06 |
1. | Remove currently installed seat following the instructions in the owner's manual. | |||||||||||||||||||||||||||||||||||||||||||||||||||
2. | For Models with Solo Seat: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1). | |||||||||||||||||||||||||||||||||||||||||||||||||||
3. | For Models with two-up Seat: At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. | |||||||||||||||||||||||||||||||||||||||||||||||||||
4. | See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear locking the retention nut in place. Remove cable strap. | |||||||||||||||||||||||||||||||||||||||||||||||||||
5. | For Models with two-up Seat: See Figure 3. Remove the four foam squares (1) from the fender. For Models with Solo Seat: See Figure 4. Remove the two foam squares (2) from the fender. | |||||||||||||||||||||||||||||||||||||||||||||||||||
6. | Remove any adhesive residue remaining on the fender with a general-purpose adhesive remover (3M™ part number 051135 or equivalent). Rinse with clear water and dry thoroughly with a clean white cloth. Clean surfaces with isopropyl alcohol. Allow to dry completely. |
Figure 1. Fender Hole Identification and Hardware Locations
Figure 2. Retention Nut Installation
Figure 3. Foam Squares and Protective Tape (Two-Up Seat)
Figure 4. Foam Squares and Protective Tape (Solo Seat) |
1. | See Figure 6. From the underside of the fender, insert the screw (9) up through the grab strap mounting hole. Secure with the plastic retention nut (10). For 2010 and Later FXDWG Models: See Figure 5. Verify that the head of the flange screw (1) is clear of the wire guide (2) is installed against the fender. NOTE One end of the new grab strap (8) has a single mounting hole, and the opposite end has two holes. | |||||
2. | Install the end of the new grab strap with the single hole over the screw threads. Bring the opposite end of the strap over the first end as shown. For all Kits EXCEPT 51381-06: Insert the screw threads through the outer hole (A). For Kit 51381-06: Insert the screw through the inner hole (B). | |||||
3. | Install the washer (11) and hex nut (12) onto the screw to secure the grab strap. Tighten to 6.8–10.2 N·m (60–90 in-lbs). | |||||
4. | Peel the adhesive backing from the protective tape (3). Carefully position the rounded notch (4) around the center fender hole or seat mounting hole (5) as shown. Smooth the tape firmly into place. | |||||
5. | See Figure 6. For Models with two-up Seats: Slide the rear of the new seat (1) through the grab strap (8). Rest the seat on the frame backbone. For Models with Solo Seats: Slide the seat toward the front until the front tang locks into the channel in the frame. | |||||
6. | Secure the seat to the fender with the knurled knob (2) and neoprene washer (3) from the kit. NOTE Ambient temperature of at least 60 °F (16 °C) for proper adhesion of the emblem to the knob. | |||||
7. | Remove the liner from the adhesive backing of the Bar & Shield emblem (4). Rotate the emblem for best appearance, and apply the emblem to the center recess on the knurled knob. Apply even pressure to the emblem for one minute for proper adhesion. |
Figure 5. Grab Strap Installation - FXDWG Models |
Kit | Item | Description (Quantity) | Part Number |
---|---|---|---|
Common items for ALL seat kits | 1 | Seat | Not sold separately |
2 | Knurled knob, 1/4-20 | 3649 | |
3 | Washer, neoprene | 6205 | |
4 | Emblem, Bar & Shield | 14628-96 | |
5 | Cable strap (installation aid) | 10039 | |
6 | Leather dressing | Not sold separately | |
7 | Protective tape | 59546-02 | |
Two-up seat kits additional contents | 8 | Grab strap | See Table 1 |
9 | Screw, hex head, 1/4-20 x 3/4 inch with washer | 3574 | |
10 | Retention nut, plastic | 7891 | |
11 | Flat washer | 6036 | |
12 | Hex nut, 1/4-20 | 7792 | |
Items referenced in text, but not included in text: | |||
A | Outermost hole, grab strap | ||
B | Innermost hole, grab strap | ||
C | Retention nut and washer |