1 | Passenger pillon |
2 | Seat post |
3 | Nut and washer |
1 | Left turn signal connector [19] (white) |
2 | Right turn signal connector [18] (black) |
1 | Left turn signal wires |
2 | Right turn signal wires |
3 | Rear turn signal connector [94] |
1. | See Figure 9. Measure the wire lengths of the OE (Original Equipment) turn signals. Cut the wire lengths on the new chrome turn signals (1) to match the length of the wires on the OE turn signals. | |||||||||||||||||||||||||
2. | See Figure 8. Assemble a chrome turn signal assembly (1) to a chrome lamp support (2) by feeding the wire leads through the wire hole in the lamp support. | |||||||||||||||||||||||||
3. | Feed the wire leads and conduit through the front hole in the license plate bracket and through hole in the support plate (4) towards the front of the vehicle. | |||||||||||||||||||||||||
4. | Thread the bolt (3) through the center hole in the support plate, through the center hole in the license plate bracket, and through the hole in the chrome lamp support into the chrome turn signal. | |||||||||||||||||||||||||
5. | Tighten the bolt to 11.3–16.9 N·m (100–150 in-lbs). | |||||||||||||||||||||||||
6. | For 2006 and Earlier Models: Route the turn signal wires between the license plate bracket and the inner fender. Access the wires through the tail lamp opening in the outer fender. | |||||||||||||||||||||||||
7. | Crimp socket terminals (4) to the ends of the turn signal wires. Refer to Service manual for crimping instructions. | |||||||||||||||||||||||||
8. | Refer to Table 1. Identify the left and right connector socket housings and match the socket terminated colored leads to the cavities in the socket housing which mate to the colored leads in the pin housing. | |||||||||||||||||||||||||
9. | Install terminated wires to appropriate cavities in socket connectors. Close secondary lock to engage side latches in connectors. | |||||||||||||||||||||||||
10. | Arrange all electrical connectors and wiring harnesses (between inner and outer fender) to either side of tail lamp opening in outer fender and away from tail lamp bulb housing. | |||||||||||||||||||||||||
11. | Install tail lamp assembly. a. Insert tabs of front of housing under forward edge of fender opening. b. Carefully push tail lamp assembly toward front. c. Engage retaining clip with rear edge of fender. Gently press down on assembly until clip locks in place. NOTE Retaining clip must engage rear fender opening for tail lamp to remain locked into position in rear fender. | |||||||||||||||||||||||||
12. | For 2007 and Later Models: Combine the wires from the rear turn signals together and wrap with electrical tape. Use fish tape to pull turn signal wires through sheathing towards front of vehicle and up to 6 pin turn signal connector. | |||||||||||||||||||||||||
13. | Crimp the socket terminals onto the turn signal wires. Refer to your Service Manual for Crimping Instructions. | |||||||||||||||||||||||||
14. | See Figure 5. Identify left and right turn signal wires and install terminated wires in appropriate cavity in 6 pin socket connector. Close secondary lock to engage side latches. | |||||||||||||||||||||||||
15. | Connect the pin terminal housing to the socket terminal housing. |
Figure 5. Turn Signal Pin Connector Locations | ||||||||||||||||||||||||
16. | See Figure 2. Reinstall connector, passenger pillion (1), seat stud (2), nut and washer (3) and seat per instructions in the Service Manual. |
Figure 6. Turn Signal Connector Cross Section
Figure 7. Turn Signal Mounting
Figure 8. Turn Signal to Support |
Connector | Cavity Number 1 | Cavity Number 2 |
---|---|---|
Left (white) [94] | V to V | BK to BK |
Right (black) [94] | V to BN | BK to BK |
1. | Install the maxi-fuse and right side cover. | |
WARNING Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) | ||
2. | Turn IGN to ON and test rear lights. a. Rear brake light b. Rear tail lamp c. Left and right turn signals |
Item | Description (Quantity) | Part Number |
---|---|---|
1 | Chrome turn signal assembly (2) | 68977-00 |
2 | Lamp support (2) | 68829-05 |
3 | Bolt (2) | 2887WA |
4 | Socket terminals (4) | 73191-96 |