0/0
BOOM! AUDIO SADDLEBAG iPOD MOUNT KIT
J053122011-07-21
GENERAL
Kit Number
76000143
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Refer to the Boom! Audio iPod® Interface Module owner's manual for compatible iPod devices.
Additional Parts Required
Prior or concurrent installation of an iPod Interface Module Kit (Part No. 76476-10) is required. This item is available separately from a Harley-Davidson dealer.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation and is available from a Harley-Davidson dealer.
Kit Contents
See Figure 2 and Table 1.
INSTALLATION
iPod Mount Installation
1. If not already done, complete the installation of the iPod Interface Module Kit per the instructions in that kit, with the following exceptions:
a. Connect the iPod cable from this kit to the round connector on the iPod module on top of the AM/FM radio case.
b. The iPod cable included in the iPod Interface Module Kit will be connected to the end of the cable from this kit.
2. Remove the right-side saddlebag from the vehicle per service manual instructions.
3. See Figure 1 , (1). Measure about 228 mm (9 in) from the rear of the saddlebag, in line with the top of the bag as shown. Drill a 16 mm (0.62 in) diameter hole in that location.
1Measure nine inches (228 mm) for hole
2iPod tether
3iPod cable path inside saddlebag
Figure 1. iPod Mount Installation to Right-Side Saddlebag
4. Remove four screws retaining the original equipment (OE) saddlebag lid tether. Install the iPod tether (2) in the orientation shown.
5. See Figure 2. Fasten the iPod tether (1) to the saddlebag side wall with the dog point screws removed earlier, and alternately tighten to 2.3–2.8 N·m (20–25 in-lbs). Fasten the iPod tether to the saddlebag lid with the hi-lo screws removed earlier, and alternately tighten to 2–2.3 N·m (18–20 in-lbs).
6. Install the right-side saddlebag to the vehicle per service manual instructions.
7. Route the iPod cable (2, installed to the iPod module earlier) under the radio and rearward, inside the wire caddy alongside other harnesses down the vehicle backbone.
NOTE
  • The connection between the two iPod cables should be positioned outside the saddlebag, near the upper shock mount.
  • Do not fasten the iPod cables too tightly with cable straps, as they are easily damaged.
8. Fasten the iPod cables with cable straps (not supplied). Route the cable through the hole drilled in the saddlebag wall.
9. Install the grommet (3) around the cable, and insert into the hole.
10. Route the cable around the inside rear of the saddlebag as shown, through the two elastic knit loops in the tether, and through the opening in the bottom of the iPod pocket. Fasten the cable to the saddlebag walls as necessary with wire clips (4).
IN USE
WARNING
Set volume levels and other controls on audio and electronic devices before riding. Distractions can lead to loss of control, resulting in death or serious injury. (00088b)
See the Boom! Audio iPod Interface Module owner's manual for operating instructions.
SERVICE PARTS
Figure 2. Service Parts, Saddlebag iPod Mount Kit
Table 1. Service Parts
Item
Description (Quantity)
Part Number
1
Tether, iPod, saddlebag lid
90200002
2
Cable, iPod, intermediate
72648-11
3
Grommet, strain relief
12100001
4
Clip, adhesive back (6)
Not sold separately