0/0
FLST (WITH FOG/PASSING LAMPS) DETACHABLE WINDSHIELD KIT
J053802017-08-22
GENERAL
Kit Number
57400110, 57400111, 57400112, 57400113, 57400114, 57400115
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts Required
NOTE
A service manual for your model motorcycle is available from a Harley-Davidson Dealer.
Kit Contents
See Figure 1 and Table 1 , Figure 2 and Table 2.
INSTALLATION
WARNING
Rider and passenger safety depend upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308b)
NOTE
Place shop rags on the headlamp and front of the fuel tank to prevent scratches to headlamp and fuel tank Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts.
Spacers on the topmost screws will fall free when the screws are removed. Take care that the spacers do not strike the fuel tank or fender, damaging the finish.
1. Remove the stock windshield, if so equipped. Discard the windshield.
NOTE
Keep front wheel straight to prevent brackets from scratching fuel tank.
2. Figure 2 and Table 2. Remove and discard the original bottom fog/passing lamp bracket screw (4) and washer (1).
3. Place a new flat washer (1), bushing (2) and flat washer (1) on a 1-3/8 inch long screw (4) from the kit. Thread the screw through the lower hole in the fog/ passing lamp bracket and decorative fork cover, and into the triple clamp. Tighten.
Torque: 10.8 N·m (8 ft-lbs) screw
4. Repeat Step 3 on the opposite side of the motorcycle.
5. Place a flat washer (1), bushing (2), and flat washer (1), on a screw (3) from the kit. Place the screw through the top hole of the fog/passing lamp bracket and through OE spacer. Tighten.
Torque: 10.8 N·m (8 ft-lbs) screw
6. Repeat Step 5 on the opposite side of the vehicle.
WARNING
Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b)
WARNING
Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a)
NOTE
Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed.
NOTE
Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components.
REMOVING THE WINDSHIELD
To remove the windshield, grab the windshield edges on each side of the center brace and firmly pull the windshield loose from the bushing grooves.
CARE AND CLEANING
NOTE
Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections.
NOTICE
Use only Harley-Davidson recommended products on Harley-Davidson windshields. Do not use harsh chemicals or rain sheeting products, which can cause windshield surface damage, such as dulling or hazing. (00231c)
Do not clean polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result.
NOTE
Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier.
Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson windshields.
SERVICE PARTS
Figure 1. Service Parts: Windshield Kits
Table 1. Service Parts: Windshield Kits
Item
Description (Quantity)
Part Number
Item
Description (Quantity)
Part Number
1
Windshield, standard height, clear
58241-95
9
Screw, button head (2) 1/4-20 x 1-1/4 inch
94426-95
Windshield, low, smoked
58277-95
10
Windshield retainer (right)
58253-95
Windshield, standard height, clear
58294-09
11
Windshield retainer (left)
58252-95
Windshield, 2 inch taller than standard, clear
57754-04
12
Nylon bushing (4)
58272-95
2
Screw, pan head, Torx (2 ) #12-24 x 13/16 inch
2452
13
Brace, vertical, right, polished
58406-75A
3
Screw, pan head, Torx (7) #12-24 x 5/8 inch
2921A
Brace, vertical, right, black
58045-09
4
Brace, horizontal, inner, polished
58431-94
14
Brace, vertical, left, polished
58408-75A
Brace, horizontal, inner, black
57690-10
Brace, vertical, left, black
58046-09
5
Brace, horizontal outer windshield, polished
58428-94
15
Tape, windshield bracket (2)
58417-77
Brace, horizontal outer windshield, black
57689-10
16
Flat washer, 1/4 inch, silver (2)
6703
6
Tape
58416-77A
17
Acorn nut, #12-24 (chrome) (9)
7651A
7
Bracket, left, polished
58291-95
18
Acorn nut, 1/4-20 (chrome) (2)
94004-90T
Bracket, left, black
Bracket left chrome
12700042
57063-00A
19
Hardware kit:
Washer, heat treated (8)
Hex socket button head screws (2)
Hex socket button head screws (2)
Bushing (4)
91800025
8
Bracket, right, polished
Bracket, right black
57062-00A
12700043
Bracket, right, chrome
57062-00A
NOTE: Appearance of actual components may vary from illustration.
Figure 2. Service Parts: Hardware Kit
Table 2. Service Parts Table
Item
Description (Quantity)
Part Number
1
Washer, 0.105 inch (2.7 mm) (8)
6400HB
2
Bushing (4)
67621-94
3
Screw, button head, 1 3/4 inch
4343
4
Screw, button head, 1 3/8 inch
4482
Items mentioned in text:
A
Decorative triple clamp cover
B
Fog/Passing lamp bracket
C
Original equipment spacer