FLHX/FLTRX LED REAR AUXILIARY LAMP
J058522013-06-28
GENERAL
Kit Number
68000119
Models
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Service Manual Required
WARNINGRider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
NOTE
This instruction sheet refers to service manual information. A service manual for this year/model motorcycle is required for this installation. One is available from a Harley-Davidson dealer.
Electrical Overload
NOTICE
It is possible to overload the vehicle's charging system by adding too many electrical accessories. If the combined electrical accessories operating at any one time consume more electrical current than the vehicle's charging system can produce, the electrical consumption can discharge the battery and cause damage to the vehicle's electrical system. (00211d)
WARNINGWhen installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified. Exceeding the maximum amperage can lead to electrical failures, which could result in death or serious injury. (00310a)
This Rear Auxiliary Lamp kit requires up to 500 mA more current from the electrical system.
PREPARATION
NOTE
For vehicles equipped with security siren:
- Verify that the Hands-Free Fob is present.
- Turn ignition switch ON.
WARNINGTo prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
- See the service manual. Remove the left saddlebag, main fuse and seat.
INSTALLATION
| 1. | See Figure 2. Assemble the auxiliary lamp bracket (7) to the auxiliary lamp (1) with two #8-32 screws (3) and lockwashers (2) from the kit. Tighten securely. | |
| 2. | Remove the two screws holding the rear light bar and license plate bracket assembly to the rear fender. | |
| 3. | Remove the two screws and lockwashers holding the license plate bracket to the rear light bar assembly. | |
| 4. | Position the auxiliary lamp and bracket assembly on top of the rear light bar assembly. Insert original screws. Tighten to 6.8–9 N·m (60–80 in-lbs). | |
| 5. | Route the auxiliary lamp wires through the rear fender grommet alongside the rear lamp wires. | |
| 6. | Fasten the rear light bar, assembly to the rear fender with the two screws removed earlier. Tighten to 9.5–16.2 N·m (84–144 in-lbs). | |
| 7. | See Figure 1. Using cable straps (6) to secure, route the auxiliary lamp wires, a. under the fender, b. over to the left side under the rear fascia, c. follow antenna lead if present, d. upward in front of the saddlebag rear mounting bracket, e. below the upper frame tube. | |
| 8. | See Figure 2. Get the three-way pin housing (5) from the kit. See the service manual appendix to insert the auxiliary lamp wires and terminals into the pin housing: |
- Blue wire to cavity 1.
- Red/yellow wire to cavity 2.
- Black wire to cavity 3.
| 9. | Obtain the adapter harness (4) from the kit. Connect the auxiliary lamp pin housing to the black three-way socket housing of the "Y"-harness. | |||||||||||||||||||
| 10. | See Figure 1. Locate the six-way rear lighting harness connector [7] in the area under the seat. | 
Figure 1. Under Seat: FLHT | ||||||||||||||||||
| 11. | Connect the LED rear auxiliary lamp "Y" harness to the vehicle rear lighting harness connector [7]. | |||||||||||||||||||
| 12. | Use two cable straps (6) from the kit to secure the auxiliary lamp harness to existing harnesses routed along the frame. |
RETURN TO SERVICE
NOTE
Verify that the ignition key switch is in the OFF position before installing the main fuse.
| 1. | See the service manual to install the main fuse. | |
| 2. | Turn the ignition key switch to IGNITION, but do not start the vehicle. Check operation of all lamps. Proper operation of auxiliary lamp is: a. The rear auxiliary lamp is always lit when the ignition is ON. b. With brake lever or brake pedal actuation, the rear auxiliary lamp brightens. | |
| WARNING After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) | ||
| 3. | Install the left side saddlebag and seat. |
SERVICE PARTS
Figure 2. Service Parts, FLHX/FLTRX LED Rear Auxiliary Lamp
Table 1. Service Parts
Item | Description (Quantity) | Part Number |
|---|---|---|
1 | Rear auxiliary lamp assembly | Not sold separately |
2 | Bracket, rear auxiliary lamp | Not sold separately |
3 | Screw, #8-32 x 9.5 mm (⅜ in) long (2) | Not sold separately |
4 | Split lockwasher #8 (2) | Not sold separately |
5 | Three-way pin housing | 73103-96BK |
6 | Cable strap (6) | 10006 |
7 | Aux lighting "Y" harness | 69200805 |
Items mentioned in text, but not included in kit. | ||
A | Rear light bar assembly | |
B | License plate bracket | |
C | 1/4-20 TORX screw and lock washer (2) | |
D | 5/16-18 hex head screw (2) | |
E | Rear fender grommet | |