0/0
SOFTAIL RIGID MOUNT SADDLEBAGS
J044742011-06-22
GENERAL
Kit Number
90419-08
Models
For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only).
Additional Parts
Docking point hardware Kit 53930-03 can use the front and rear docking points in the kit for the installation of the saddlebags. This will also permit the use of the detachable luggage rack, Kit 53612-08 or the sissy bar upright, Kit 52729-08.
WARNING
Rider and passenger safety depend upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333b)
Kit Contents
See Figure 1 and Table 1.
INSTALLATION
NOTE
Maximum saddlebag load is 10 lbs. (4.5 kg) for each bag.
WARNING
Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a)
NOTE
Saddlebag hangers must be mounted with the bend in the hanger facing out from the motorcycle.
NOTE
The saddlebags are symmetrical and can be mounted on either side.
1. See Figure 1. Remove the fender support cover screws from locations shown for mounting saddlebags.
2. Place lock washers (6) on two cap screws (5) and insert through the top holes of the saddlebag hanger.
NOTE
The FXSTC Does Not use narrow spacers (8) in Step 3 for the saddlebag installation.
3. With the cap screws in place on the hanger, place a wide spacer (7) followed by a narrow spacer (8) on each screw.
4. Thread the cap screws into the location of the original screws previously removed in Step 1 and tighten screws to 30 N·m (22 ft-lbs).
5. From the inside of the saddlebag install two button head screws (2) with washers (3) through the upper mounting holes in the saddlebag and the hanger.
6. On the backside of the hanger install hex nuts (4) to the screws from previous step and tighten to 30 N·m (22 ft-lbs).
7. Insert two button head screws through the lower two holes on the backside of the hanger and into the saddlebag.
8. From the inside of the saddlebag install washers and hex nuts to screws and tighten to 30 N·m (22 ft-lbs).
9. Repeat Steps 1 through 8 for installation of the other saddlebag.
Installation with Docking Points
  1. If you choose to use the docking points from Kit 53930-03, repeat the installation of previous Steps 1-8 and substitute the front and rear docking points for the spacers (7) in this Kit. You must use narrow spacers (8) from this kit for both the FLSTSB and the FXSTC when using the docking points.
Install Reflectors
WARNING
Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b)
  1. Measure approximately 1-1/2 in. (38 mm) from the bottom edge of the saddlebag. Orient the reflector horizontally and carefully center the reflector mount between the straps of the saddlebags.
  2. See Figure 1. Position reflector mount (10) on saddlebag.
  3. Mark holes on saddlebag with pen (or other appropriate tool).
  4. Using soapy water, clean surface of saddlebag where reflector will be installed.
  5. Allow the surface to dry completely before continuing.
  6. Using appropriate tool, make two 3/16 in. holes in saddlebag.
  7. Install reflector mount (10) on saddlebag using two push nuts (11).
  8. Remove backing from adhesive on reflector (12) and install on mount (10).
  9. Let the adhesive cure for at least 24 hours at no less than 60°F (16°C).
SERVICE PARTS
Figure 1. Service Parts: FLSTB and FXSTC Saddlebags
Table 1. Service Parts Table
Item
Description (Quantity)
Part Number
1
Hardware kit (includes items 2 through 12)
90492-08
2
  • Button head TORX® screw, T45 (8)
4163
3
  • Plain washer, Type A (8)
6416
4
  • Nylon cap hex nut (8)
7893
5
  • Hex cap screw (4)
9469
6
  • Lock washer (4)
7038
7
  • Wide spacer, special (4)
Not Sold Separately
8
  • Narrow spacer, special (4)
Not Sold Separately
9
Reflector kit, includes items 10 through 12 (2)
59480-04A
10
  • Reflector mount
Not Sold Separately
11
  • Pushnut (2)
8126A
12
  • Reflector, red
59269-10
13
Saddlebag hanger, right side
90446-08
14
Saddlebag hanger, left side
90440-08
15
Saddlebag assembly (2)
90490-08
16
Disconnect buckle (2)
90495-08
Items mentioned in text, but not included in kit:
A
Fender rail support cover