Speedometer
WARNING
Travel at speeds appropriate for road and conditions and never travel faster than posted speed limit. Excessive speed can cause loss of vehicle control, which could result in death or serious injury. (00008a)
See Figure 1. The speedometer registers miles per hour (U.S. models only) or kilometers per hour (international models only).
Tachometer
See Figure 1. The tachometer shows the engine speed in revolutions per minute (RPM x 1000).
Odometer
Pressing the TRIP switch will activate the odometer reading.
The following items can be viewed through the odometer window:
Press and release the TRIP switch to cycle through the displays.
Trip Odometers A and B
To check mileage or to reset trip odometers, press and release the TRIP switch until the desired trip odometer register (A or B) is displayed. An A or B in the upper left of the display window identifies the trip odometer.
To reset or zero trip odometers, have desired (A or B) odometer in display window. Press the TRIP switch and hold for approximately three seconds. The trip odometer will be reset to zero.
Gear Selection
Press and release the TRIP switch to cycle through the odometer window displays to the gear number display. The gear number will read 1-6.
In neutral or with the clutch lever pulled in, the gear number in the display will be blank.
Time
Press and release the TRIP switch to cycle through the odometer window displays to the time display. To set the time:
  1. Push the OFF/RUN switch to the RUN position.
  2. See Figure 1. Press and release the TRIP switch until time (hour and minutes) is displayed. Press and hold the TRIP switch until 12HR begins to blink in the speedometer display window. Release the switch.
  3. Press and release the TRIP switch once to advance to a blinking 24HR or military style time display. Each time you press and release the switch, the display will switch between 12HR and 24HR.
  4. When the desired time style is displayed, press and hold the TRIP switch for until the hours display is blinking.
  5. Press and release the TRIP switch repeatedly to advance the hours.
  6. When the correct hour is displayed, press and hold the TRIP switch until the minutes display starts blinking.
  7. Press and release the TRIP switch repeatedly to advance the minutes display.
  8. When the correct minutes are displayed, press and hold the TRIP switch until the display advances to the selection of AM or PM.
    9. NOTE
    AM or PM will not appear in the regular time display. The motorcycle uses the selection for diagnostic purposes.
  9. In the 12HR display, AM or PM will appear flashing. Select AM or PM with the TRIP switch and press and hold the switch for five seconds.
  10. Put the OFF/RUN switch in the OFF position.
Fuel Range
The fuel range display shows the approximate mileage available with the amount of fuel left in the fuel tank.
With the OFF/RUN switch in the RUN position, press the TRIP switch until fuel range is displayed, as indicated by the letter "R" in the left side of the display. The calculated remaining distance (miles or kilometers) to empty is displayed, based on the amount of fuel in tank. Range can be accessed at any time using the TRIP switch.
NOTE
The fuel range and low fuel warning features are not active on early production vehicles. See an authorized Harley-Davidson dealer to have the latest calibration installed to activate these features.
Low Fuel Warning
When the low fuel warning lamp illuminates, the fuel range feature will automatically be displayed in the odometer window. The rider can press the TRIP switch to return to the cycle of odometer displays. The fuel range warning will not be repeated until the OFF/RUN is cycled to OFF and back to RUN.
After the fuel range drops to 16 km (10 mi) remaining, the fuel range display will scroll "Range Lo" to indicate that the motorcycle will shortly run out of fuel.
Resetting the low fuel warning lamp and range requires an ignition cycle change.
Disable: To disable this function while riding, press and hold the TRIP switch while in the fuel range display mode. Automatic range pop-up feature will show that it is disabled by blinking twice.
Enable: To enable the automatic low fuel warning range display, press and hold the TRIP switch. The low fuel range will blink once when the automatic feature is enabled.
NOTE
  • When the low fuel warning lamp turns on, the fuel level is low. Refuel as soon as possible.
  • The range display is only updated when the vehicle is moving.
  • The automatic fuel range display is enabled after the OFF/RUN switch is turned to OFF then to RUN.
Tip Indicator
WARNING
If tip occurs, check all controls for proper operation. Restricted control movement can adversely affect the performance of the brakes, clutch or ability to shift, which could result in loss of vehicle control and death or serious injury. (00350a)
Should motorcycle be tipped over, the word "tIP" will appear in the odometer window. Engine will not start until reset.
Reset: To reset, bring the motorcycle to the upright position. Set the OFF/RUN switch to OFF then back to RUN.
"No Fob"
If the motorcycle is ridden off without the fob, "NO FOB" will appear in the odometer window for 10 seconds after the motorcycle starts moving. With the motorcycle separated from its assigned fob, the motorcycle can only be restarted with a manual PIN entry to disarm the security system. See HARLEY-DAVIDSON SMART SECURITY SYSTEM → Arming and Disarming.
1Tachometer
2Speedometer
3Odometer
4Check engine lamp
5ABS lamp
6Cruise control
7Low fuel lamp
8Sixth gear lamp
9Battery charging
10Security system lamp
Figure 1. Speedometer
1Speedometer
2Fuel gauge
3Indicator lamps
Figure 2. Instruments