Speedometer
WARNINGTravel at speeds appropriate for road and conditions and never travel faster than posted speed limit. Excessive speed can cause loss of vehicle control, which could result in death or serious injury. (00008a)
See Figure 1. The speedometer registers miles per hour (MPH) or, on International models, kilometers per hour (KPH).
The speedometer includes a single display window for the odometer, two trip-odometers, tip indicator, and clock.
See Figure 2. Press the function button to change the display window on the speedometer face to either odometer, trip-odometer, or clock.
Odometer
See Figure 1. The odometer registers the number of miles/kilometers the vehicle has traveled. The odometer can display mileage when the motorcycle is on or off by pressing the function button. There is no need to turn the motorcycle on to check the odometer reading.
Trip Odometer
Use the trip-odometer A or trip-odometer B to register number of miles/kilometers traveled on a trip or between refueling. The ignition/headlamp key switch must be in the IGNITION or ACCESSORY position to view or reset the trip-odometers.
See Figure 1. To view the trip-odometer, press the function button until an A or B is displayed in the upper left corner of the odometer window.
To reset a trip-odometer to zero, press the function button to select the trip-odometer to be reset. Press and hold the function button for approximately 2-3 seconds until the trip-odometer resets to zero.
NOTICE
Never attempt to tamper with or alter the vehicle odometer. This is illegal. Tampering with or altering a vehicle odometer may cause equipment damage. (00160a)
Tip Indicator
WARNINGIf tip occurs, check all controls for proper operation. Restricted control movement can adversely affect the performance of the brakes, clutch or ability to shift, which could result in loss of vehicle control and death or serious injury. (00350a)
Should motorcycle be tipped over, the word "tip" will appear in the odometer window. Engine will not start until reset. To reset, cycle the ignition/headlamp key switch IGNITION-OFF-IGNITION.
Tachometer
NOTICE
See OPERATING RECOMMENDATIONS section. Do not operate the engine above maximum safe RPM as shown under OPERATION (red zone on tachometer). Lower the RPM by upshifting to a higher gear or reducing the amount of throttle. Failure to lower RPM may cause equipment damage. (00159a)
See Figure 1. The tachometer measures the engine speed in revolutions per minute (RPM).
Clock
The clock displays time in a 12-hour or 24-hour format. To view the clock, press the function button until the clock (hour and minutes) displays in the odometer window.
The clock can display time when the motorcycle is on or off by pressing the function button. There is no need to turn the motorcycle on to check the clock.
Setting the Clock
- Turn the ignition/headlamp key switch to IGNITION or ACCESSORY.
- See Figure 2. Press the function button until the clock (hour and minutes) displays in the odometer window.
- Press and hold the function button for approximately five seconds until 12HR begins to blink in the odometer window. Release the button.
- Select 12HR or 24HR (military style) time display by pressing and releasing the function button. When the desired time style is selected, press and hold the function button for approximately five seconds until the hours display starts blinking.
- The hour display will advance one hour each time the function button is pressed and released. Press and release the function button repeatedly to select the appropriate hour. When the correct hour is displayed, press and hold the function button until the minutes display starts blinking.
- The minutes display will advance one minute each time the function button is pressed and released. Press and release the function button repeatedly to select the appropriate minutes. When the correct minutes are displayed, press and hold the function button until the minutes display stops blinking. This indicates that the clock has been set.
- Turn the ignition/headlamp key switch to the OFF position.
NOTE
There is no AM or PM time setting required. When the correct hour is selected, press and hold the function button to advance to the minutes setting.
| 1 | Speedometer |
| 2 | Odometer/trip odometer/clock |
| 3 | Check engine lamp |
| 4 | Low fuel warning lamp |
| 5 | Sixth gear lamp |
| 6 | Battery lamp |
| 7 | Security system lamp |
| 8 | Tachometer |
Figure 1. Speedometer/Odometer and Tachometer
| 1 | Speedometer/odometer |
| 2 | Function button |
| 3 | Indicator lamps |
| 4 | Tachometer |
Figure 2. Instruments: FXDSE2