NOTE

When checking the transmission lubricant level, motorcycle should be standing STRAIGHT UP, not leaning on the jiffy stand. Keep motorcycle upright for a short time to equalize lubricant level in the transmission compartments.

Drain and refill the transmission with fresh lubricant at proper intervals. For best results, drain lubricant while hot. Refer to Service Intervals and Records → Service Records.

WARNING

Be sure that no lubricants or fluids get on tires, wheels or brakes when changing fluid. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury. (00047d)

NOTICE

When draining or adding lubricant, do not allow dirt, debris or other contaminants to enter the engine. (00198a)

NOTICE

Do not overfill the primary chaincase with lubricant. Overfilling can cause rough clutch engagement, incomplete disengagement, clutch drag and/or difficulty in finding neutral at engine idle. (00199b)

Check Lubricant Level

1.	Run motorcycle until engine is at normal operating temperature.
2.	Position motorcycle straight up.
	WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
3.	Turn off ignition switch and STOP/RUN switch.
4.	XL models with mid-mount controls: See Figure 3. Remove screws and detach the rider footrest support bracket from the left side of the vehicle.
5.	See Figure 1. Remove screws with washers from clutch inspection cover. Remove clutch inspection cover from primary cover. NOTE The filler access is the clutch inspection cover.
6.	See Figure 2. Verify that lubricant level is even with bottom of clutch diaphragm spring. NOTE Add only enough of FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT through clutch inspection cover opening until the lubricant reaches the bottom of clutch diaphragm spring.
7.	Install the clutch inspection cover. a. Install new quad ring. b. Verify that quad ring is fully seated in groove of primary cover. c. Install clutch inspection cover. Secure with six screws. d. Tighten in a crosswise pattern. Torque: 9.5–12.2 N·m (84–108 in-lbs) Clutch inspection cover screw
8.	If the left footrest assembly was removed, install support bracket with two screws. Tighten screws. Torque: 61–67.8 N·m (45–50 ft-lbs) Rider footrest support bracket mounting screw
9.	Install main fuse.
10.	Start engine. Check for any lubricant leaks.
11.	Turn off engine.

1	Clutch inspection cover
2	Drain plug
3	Primary chain inspection cover

Figure 1. Primary Cover

1	Clutch diaphragm spring
2	Clutch adjusting screw
3	Quad ring
4	Primary cover
5	Chaincase lubricant level

Figure 2. Chaincase Lubricant Level

Changing Lubricant

1.	Run motorcycle until engine is at normal operating temperature.
2.	When the engine reaches normal operating temperature, park motorcycle on jiffy stand. This allows the chaincase lubricant to drain out of transmission.
	WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b)
3.	Turn off ignition switch and STOP/RUN switch.
4.	See Figure 1. Position a suitable container under transmission drain plug (2).
5.	The drain plug is located under the clutch, on the underside of the primary cover. Remove drain plug and drain lubricant.
6.	Position the motorcycle STRAIGHT UP and LEVEL. This allows more fluid to drain from the clutch compartment. NOTE Dispose of lubricant in accordance with local regulations.
	NOTICE Do not over-tighten filler or drain plug. Doing so could result in a lubricant leak. (00200b)
7.	Clean magnetic drain plug. Replace drain plug O-ring if damaged.
8.	Apply LOCTITE 565 PIPE SEALANT WITH TEFLON to the drain plug. Install and tighten drain plug. Torque: 19–40.7 N·m (14–30 ft-lbs) Primary chaincase drain plug
9.	XL models with mid-mount controls: See Figure 3. Remove screws (2) and detach the rider footrest support bracket (1) from the left side of the vehicle.
10.	See Figure 1. Remove screws with washers from clutch inspection cover (1). Remove clutch inspection cover from primary cover. NOTE The filler access is the clutch inspection cover.
11.	See Figure 2. Add FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT through clutch inspection cover opening until the lubricant reaches the bottom of clutch diaphragm spring. Volume: 0.95 L (1 qt)
12.	Install the clutch inspection cover. a. Install new quad ring (3). b. Verify that quad ring is fully seated in groove of primary cover. c. Install clutch inspection cover. Secure with six screws. d. Tighten in a crosswise pattern to 9.5–12.2 N·m (84–108 in-lbs).
13.	If the left footrest assembly was removed, install support bracket with two screws. Tighten screws. Torque: 61–67.8 N·m (45–50 ft-lbs) Rider footrest support bracket mounting screw
14.	Install main fuse.
15.	Start engine. Check for any lubricant leaks.
16.	Turn off engine.

1	Support bracket
2	Screws (2)

Figure 3. Mid-Mount Rider Footrest Assembly