Hazard Warning 4-Way Flasher
See Figure 1. The hazard switch (1) is used to leave a stranded motorcycle in the 4-way flashing mode. With the flashers, the motorcycle can be left with the ignition off until assistance is found. Refer to Table 1.
  1. With the OFF/RUN switch in the run position, press on the hazard warning triangle to activate the 4-way flashers.
  2. NOTE
    • The fob must be present when turning on the 4-way flashers and when canceling the flashers.
    • The four-way flashers will operate when the vehicle is tipped over regardless of OFF/RUN switch position. See Operation → Starting after Tipover.
  3. Turn OFF/RUN switch to the off position. The 4-way flashers continue for 2 hours or until cancelled by the rider.
  4. To cancel, turn the OFF/RUN switch to the run position. Press the warning triangle above the start switch.
OFF
See Figure 1. Press the engine OFF/RUN switch to off (2) to shut off the engine. Refer to Table 1.
RUN
See Figure 1. Push the engine OFF/RUN switch to run (3) to enable engine start and run. The engine OFF/RUN switch must be in the run position to start or operate the engine. Refer to Table 1.
Right Turn Signal
Activate:
See Figure 1. Press the right turn signal switch (4) to activate the right turn signal. Refer to Table 1.
Cancel:
Manual Operation: Press the right turn signal switch to cancel the right turn signal.
Automatic Operation: The turn signal lamps automatically cancel when a full turn has been detected based on speed, acceleration and turn completion.
The lamps also cancel if the turn signal has been activated for a prolonged period (20 flashes) while the motorcycle speed is greater than 7 mph (11 km/h). If the motorcycle is stopped or moving slower than this speed, the turn signal continues flashing.
NOTE
Front turn signal lamps also function as running lamps. This feature may not be available in all markets.
CURSOR/SELECT Switch
See Figure 1. The CURSOR/SELECT five-way switch (5) operates radio features on equipped vehicles. See the BOOM! BOX OWNER'S MANUAL. Refer to Table 1.
SELECT: Press the SELECT switch straight in to select or toggle a feature on the radio screen.
CURSOR: Press the switch in the desired direction to move the cursor or selection on the radio screen.
Back switch
See Figure 1. The back switch (6) operates radio features on equipped vehicles. See the BOOM! BOX OWNER'S MANUAL. Refer to Table 1.
Start/Reverse
Start:
  1. Turn ignition switch to IGNITION.
  2. Figure 1. Switch the OFF/RUN switch to the run position (3). Shift the transmission to neutral. The neutral (green) indicator illuminates. See Operation → Starting the Engine.
  3. Press the start switch (7) to operate the starter motor. Refer to Table 1.
  4. NOTE
    • When the starter is activated, the headlamp is momentarily turned off to reduce battery load.
    • If the engine does not start, the starter motor runs for ten seconds and stops. Release the start switch. Press the start switch to try again. After several unsuccessful attempts to start the engine, see a Harley-Davidson dealer.
Reverse:
The reverse control switch operates the electric reverse motor once the engine is running and transmission is in neutral. The reverse enable indicator is lit when reverse operation is enabled. See Operation → Reverse Operation for detailed operation.
1Hazard warning
2Off
3Run
4 Right turn signal
5 Cursor/Select
6 Back
7Start/Reverse
Figure 1. Right Hand Switch Module
Table 1. Right Hand Control Switches
SWITCH
NAME
FUNCTION
Hazard
Press to activate the 4-way flashers.
Off
Press to stop the engine or to prevent the engine from starting.
Run
Press to allow the engine to start.
Right turn
Press to signal a right turn.
Cursor/Select
Five-way switch, operates radio functions.
Back
Press to go back to previous screen on radio.
Start/Reverse
Press to start the engine.
Engine running:Press to engage reverse.