See Figure 1. The odometer shows the total accumulated mileage for the motorcycle. Press the trigger switch to cycle through different odometer functions. The time and odometer can be displayed while the motorcycle is turned off by pressing the trigger switch.

Changing units: With odometer displayed, press and hold the trigger switch until the units change to MI or KM. All odometer functions display the selected units.

See Figure 1. The two trip odometers (A and B) display the total accumulated mileage since they were last reset. To check, press and release the trigger switch until the desired trip odometer (A or B) is displayed.

Reset: With the desired trip odometer displayed (A or B), press and hold the trigger switch until the selected trip odometer resets to zero.

See Figure 1. The fuel range display shows the approximate mileage available with the amount of fuel left in the fuel tank. The range display is only updated when the vehicle is moving.

Display Fuel Range: With the ignition switch in the ACCESSORY or IGNITION position, press the trigger switch until fuel range is displayed. The fuel range is indicated by the letter "R" in the left side of the display. The calculated remaining distance (miles or kilometers) to empty is displayed, based on the amount of fuel in the tank.

Low Fuel: Refer to Specifications → Specifications → Capacities. The fuel range is automatically displayed in the odometer window when the low fuel lamp is on. When fuel range drops to 10 miles or 10 kilometers remaining, the odometer window displays "LO RNG" to indicate that the motorcycle is nearly out of fuel. Refuel as soon as possible.

Turn Off Automatic Low Fuel Popup: With the fuel range displayed, hold the trigger switch until the fuel range flashes two times. To turn this feature back on, hold the trigger switch until the fuel range flashes once.

Reset: Resetting the low fuel warning lamp and fuel range requires sufficient fuel in the tank and an ignition cycle change (IGNITION-OFF-IGNITION).

Adding at least 7.5 L (2 USgal) of fuel allows the fuel range to update. The fuel range slowly updates over the next 50 km (30 mi) after refueling.

Battery Reconnection and Initialization: If the battery is disconnected and reconnected, the gauge requires approximately a half tank of fuel to initialize fuel range functionality.

See Figure 1. The speed capture display allows for the recording vehicle speed when pacing another vehicle. The speed capture display is only updated when the vehicle is moving.

Activation: With the ignition switch in the ACCESSORY or IGNITION position, press the trigger switch until speed capture is displayed. This feature is indicated by the letters "SP" in the left side of the display. Press and hold the trigger switch to activate the speed capture The speed is displayed, based on motorcycle speed.

Capture: While traveling at speed, press and hold the trigger switch to save the current speed. This is indicated by the letter "C" on the right side of the display.

Press and hold the trigger switch to erase the current saved speed or to reactivate the speed capture function.

See Figure 1. On equipped models, the currently selected gear (1-6) is displayed in the odometer window. The gear indicator is calculated from the vehicle speed and engine speed. The gear indicator remains blank when the transmission is in neutral, the clutch lever is pulled in or the vehicle is not moving.

The gear indicator may be momentarily inaccurate depending on rider clutch use characteristics and clutch wear. This can occur if the clutch is allowed to slip either due to excessive wear, misadjusted clutch or if the operator rides the clutch.

See Figure 1. If the motorcycle is tipped over, the word "tIP" appears in the odometer window. The engine does not start until reset.

To reset the odometer tIP message, see Operation → Starting after Tipover.

If the motorcycle has a security system and is driven off leaving the fob behind, 'NO FOB' temporarily displays in the odometer window.

With the motorcycle separated from its assigned fob, the motorcycle can only be started with a manual PIN entry to disarm the security system. See SECURITY SYSTEM → Arming and Disarming.

See Figure 1. Some vehicles have a jiffy stand interlock feature. A "SidE StAnd" message scrolls across the odometer if the jiffy stand is lowered while the motorcycle is in gear or while riding. See Before Riding → Jiffy Stand Interlock.

Clearing message (before starting motorcycle): Place transmission in neutral or raise jiffy stand.

Clearing message (while riding): Safely bring the motorcycle to a stop. Raise jiffy stand.

Clearing message (temporarily): Press the trigger switch. The message clears momentarily before displaying again.

See Figure 2. The time is displayed in the odometer window. Perform the following steps to configure time.