The transmission lubricant level should be checked monthly.
Your motorcycle comes equipped with Screamin' Eagle SYN3 Synthetic Motorcycle Lubricant. For transmission lubrication, it is not recommended to mix SYN3 with other lubricant products.
The transmission should be drained and refilled with fresh lubricant at proper intervals. Refer to Refer to Maintenance Scheduling → Service Records..
NOTE
When checking the transmission lubricant level, the motorcycle should be leaning on the jiffy stand. Allow a short time to equalize lubricant level in the transmission compartments.
Check Lubricant Level
1. Park motorcycle on a level surface on jiffy stand.
2. See Figure 1. Remove the threaded filler plug/dipstick by turning the plug counterclockwise.
3. See Figure 2. Wipe off filler plug/dipstick and place it back in the filler hole. Do not screw in. (Dipstick should rest on threads of the case.)
4. Remove the plug/dipstick. Check the level. The lubricant level should be between the ADD and FULL lines on the dipstick.
WARNING
Be sure that no lubricants or fluids get on tires, wheels or brakes when changing fluid. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury. (00047d)
NOTICE
When draining or adding lubricant, do not allow dirt, debris or other contaminants to enter the engine. (00198a)
5. If the lubricant level is below the ADD mark, add lubricant. Do not overfill (bringing the level above the FULL mark) or leakage may occur. Approximate transmission fluid capacity.
Volume: 0.83–0.95 L (28–32 fl oz)
NOTE
  • When filling the transmission, use Screamin' Eagle SYN3 Synthetic Motorcycle Lubricant (Part No. 99824-03, U.S. quart).
  • If SYN3 is not available and addition of lubricant to the transmission is required, SYN3 must be completely drained before using other lubricant products. A residual amount of fluid will remain. It is not required to flush out the residual fluid.
6. Inspect O-ring for tears or damage. Replace if required. Wipe any foreign material from plug.
7. Install threaded filler plug/dipstick. Tighten.
Torque: 2.8–8.5 N·m (25–75 in-lbs) Transmission filler plug/dipstick
Figure 1. Transmission Filler Plug/Dipstick Location
1FULL
2ADD
Figure 2. Transmission Filler Plug/Dipstick Lubricant Level
Changing Transmission Fluid
1. See Figure 1. Remove the transmission filler plug/dipstick.
2. See Figure 3. Remove transmission drain plug and drain lubricant into a suitable container.
NOTE
Dispose of lubricant in accordance with local regulations.
NOTICE
When draining or adding lubricant, do not allow dirt, debris or other contaminants to enter the engine. (00198a)
WARNING
Be sure that no lubricants or fluids get on tires, wheels or brakes when changing fluid. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury. (00047d)
3. Replace drain plug O-ring if damaged. Wipe any foreign material from plug.
4. Install drain plug. Tighten.
Torque: 19–28.5 N·m (14–21 ft-lbs) Transmission drain plug
5. Fill the transmission with Screamin' Eagle SYN3 Synthetic Motorcycle Lubricant (Part No. 99824-03, U.S. quart). Do not overfill or leakage may occur.
Volume: 0.83–0.95 L (28–32 fl oz)
6. Install threaded filler/check plug. Tighten.
Torque: 2.8–8.5 N·m (25–75 in-lbs) Transmission filler plug/dipstick
7. Start engine and carefully check for oil leaks around drain plug.
8. See Figure 2. Bring vehicle to operating temperature. Add oil to bring level to full (1) on dipstick.
9. Install threaded filler/check plug. Tighten.
Torque: 2.8–8.5 N·m (25–75 in-lbs) Transmission filler plug/dipstick
Figure 3. Transmission Drain Plug