Alert

See Figure 1. The alert icon displays information related to specific vehicle faults and matches the illuminated lamp along with a description of the current fault.

1	Alert icon
2	Alert description

Figure 1. Alert Display

Table 1. Instrument Alert Displays

Text	Cause	Action
Alert – Shutdown Alert	Propulsion will start disable sequence	See dealer
Alert – High Voltage (HV) Disconnected	HV connection issue	See dealer
Alert – Motor Fault	Motor or inverter fault	See dealer
Alert – Rechargeable Energy Storage System (RESS) Fault	RESS internal fault	See dealer
Alert – Charge Bike Fault	RESS too low to enable propulsion	Charge motorcycle
Alert – Charger Fault	Onboard Charger (OBC) general fault	See dealer
Alert – RESS Significantly Out of Balance	RESS at significant level of imbalance	See dealer
Alert – Jiffy Stand Not Trusted	Jiffy Stand Sensor (JSS) fault	Cycle jiffy stand down and back up, if the alert is not corrected see dealer
Alert – 12 V Battery Faulted	12 V Battery needs replacement	See dealer
Alert – 12 V Battery Weak	12 V Battery needs replacement	See dealer
Alert – 12 V Battery Disconnected	12 V battery leads loose or disconnected	See dealer
Alert – Load Shedding	12 V battery fault	See dealer
Alert – Low Charge	Low State of Charge (SOC)	Charge motorcycle
Alert – Coolant Pump Fault	Coolant pump fault.	See dealer
Alert – Malfunction Indicator Lamp (MIL)	Propulsion system fault.	See dealer
Alert – OBC Too Warm	OBC general fault	See dealer
Alert – RESS Too Warm	RESS general fault	See dealer
Alert – Charge Port Fault	Charge Port fault	See dealer
Alert – Electric Vehicle Supply Equipment (EVSE) Fault	EVSE fault	See dealer
Alert – Charge Plug Latch Pressed	Charge Plug latch pressed	Reinstall Charge Plug, if the alert is not correct see dealer
Alert – Load Shedding	General fault	Verify RESS has adequate charge, if the alert is not corrected see dealer
Alert – Low Charge	Low RESS charge	Charge vehicle, if the alert is not corrected see dealer
Alert – Vehicle Motion Detected	Vehicle Motion Detected	Cycle OFF/ RUN switch, if the alert is not corrected see dealer
Alert – Vehicle Starting up	Vehicle start up has been activated	Vehicle start up has been activated
Alert – Propulsion Enabled	Propulsion has been activated	Propulsion has been activated
Alert – Propulsion Limited	Low SOC, ride mode selected or general fault	Charge vehicle If unable to charge, see dealer
Alert – Check Tire Pressure	Low tire pressure	Properly inflate tires to correct pressure
No FOB	No assigned fob detected	Bring assigned fob within range
Low FOB battery	Battery in fob low	Replace fob battery

Range

See Figure 2. The Range screen displays percent of remaining charge (1, 3) and odometer (2).

NOTE

If charge state bar (1) continues to pulse after reaching 100% the RESS is performing cell balancing. Charging has completed and normal operation is available.

1	Charge state bar
2	Estimated range
3	Remaining RESS charge

Figure 2. Range Screen

Trip

See Figure 3. The trip screen displays the odometer reading (1), trip A (2) and trip B (3) mileage. The trip screen can also be configured from the settings menu to display trip K.

1	Trip A
2	Estimated range
3	Trip B

Figure 3. Trip Screen

Bluetooth

In order to leverage Bluetooth enabled functions such as Navigation, Media display and controls, the phone must be paired through the LiveWire S2 App.

Once paired, the Bluetooth icon displays phone connection status, device name and battery percentage.

Navigation

See Operation → Indicators → Menu Selections. Selecting the bike status card (3) on the navigation display is intended to assist you when traveling. Always use personal judgment and observation of the actual road conditions while riding. In some circumstances, information provided in the navigation display may be incomplete, incorrect or outdated. Road conditions, traffic laws and restrictions (such as no left turns, street closures, one way streets, road construction detours, and so on) can frequently change. Before following any instruction from the screen, check that the instruction can be done safely and legally.

If necessary, safely park the vehicle if there is difficulty following the route guidance or if there is a need to program a new route.

Program and review navigation routes with the vehicle stopped. Follow these steps to load navigation instructions.

1.	Ensure the LiveWire S2 App is in proper state before pairing.
2.	Verify the phone is connected via Bluetooth to the Livewire instrument module (Bluetooth icon is blue).
3.	Select the Navigation screen on the instrument display. It’s normal to see “No Nav” in the display prior to a route being pushed to the instrument.
4.	Open the LiveWire S2 App on your phone.
5.	Select a route or a Point Of Interest (POI), then click the action boxes: Take Me There (not “send to bike”), then Continue, Start, and finally Let’s Ride a. Turn By Turn (TBT) navigation should be running on the app and appear on the screen of the instrument display in place of where “No Nav” was previously displayed. b. If TBT does not push to the instrument, close the app and re-open it and repeat step 3.

Plan and review the route before riding the motorcycle.

See Figure 4. The navigation screen displays turn by turn navigation information that has been entered into the connected device using the LiveWire S2 App. This information includes street name (1), Next action icon (2), distance to next action (3) and time information (4) (either arrival time or trip duration).

1	Next action
2	Miles to go in trip
3	Time information
4	Minutes left in trip

Figure 4. Navigation Screen

Table 2. Navigation Icons

ICON	DESCRIPTION
	Start
	Finish
	Ended
	Navigation paused
	Navigation cancelled
	No signal
	Unidentified
	Straight
	Turn left
	Turn right
	Light left
	Light right
	Heavy left
	Heavy right
	U-Turn left
	U-Turn Right
	Keep left
	Keep right
	Keep middle
	Enter highway left
	Enter highway right
	Keep left highway
	Keep right highway
	Leave highway left
	Leave highway right
	Roundabout left⁽¹⁾
	Roundabout right⁽¹⁾
	Ferry

(1) The number in the center of the icon corresponds to the exit to be taken, counted from the entry into the roundabout.

Music

See Figure 5. The music screen displays music information from a connected device. This information includes song duration (1), artist and album (2) and song title (3).

NOTE

Must be used with a connected device through a connected headset.

Integration with hand control functionality (play, pause, volume. etc) is only through LiveWire S2 App.

1	Song duration
2	Artist and album
3	Song title

Figure 5. Audio Screen