Consumables

DescriptionPart NumberSize
LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE)99642-976 ml (¼ fl oz)
Removal
Round air cleaner
  1. See Figure 1 or Figure 2. Remove air cleaner cover.
    1. Remove screws (1).
    2. Remove cover (2).
  2. Remove filter element.
    1. Remove screws (6).
    2. Remove filter element (4) while pulling breather tube (5) from element.
  3. Remove breather tube (5) from breather bolts.
  4. Inspect the breather tube and fittings for damage. Replace if necessary.
  5. Clean and inspect the filter element. Replace if necessary.
Oval air cleaner
  1. See Figure 3. Remove air cleaner trim insert.
    1. Remove trim insert screws (1).
    2. Remove trim insert (2).
  2. Remove cover and filter element.
    1. Remove screws (3).
    2. Remove cover (4).
    3. Remove filter element (5).
  3. Clean and inspect the filter element. Replace if necessary.
Cleaning Filter Element
NOTE
  • Do not strike filter element on a hard surface to dislodge dirt.
  • Do not use air cleaner filter oil on the Harley-Davidson paper/wire mesh air filter element.
    WARNING
    Do not use gasoline or solvents to clean filter element. Flammable cleaning agents can cause an intake system fire, which could result in death or serious injury. (00101a)
  1. Clean filter element.
    1. Wash the filter element and breather tubes in lukewarm water with a mild detergent.
    2. Allow filter element to air dry or use low-pressure compressed air from the inside.
    3. Hold the filter element up to a strong light source. The element is sufficiently clean when light is uniformly visible through the media.
    4. Replace the filter element if damaged or if filter media cannot be adequately cleaned.
Rain Sock
If equipped with oval air cleaner: See Figure 3. In wet or rainy conditions, because the filter element is exposed, water can enter the engine. When parked, water can cause internal engine corrosion or damage. When running, water can cause the engine to misfire. In wet or rainy conditions, install the rain sock (6) over the air cleaner assembly to minimize water intrusion.
Installation
Round air cleaner
  1. See Figure 1 or Figure 2. Install filter element.
    1. Install breather tube (5) onto breather bolts.
    2. Install filter element (4) while pushing breather tube into element.
    3. Install screws (6). Tighten to 5.4–8.1 N·m (48–72 in-lbs).
  2. Verify that rubber seal (3) is properly seated and not damaged. Replace if necessary.
  3. Install air cleaner cover.
    1. Apply LOCTITE 243 MEDIUM STRENGTH THREADLOCKER AND SEALANT (BLUE) (99642-97) to threads of screw (1).
    2. Install cover (2).
  4. Install screw (1).
    1. Single-screw cover: Tighten to 5.6–7.3 N·m (50–65 in-lbs).
    2. Five-screw cover: Install screws (1). Tighten in a star pattern to 5.4–8.1 N·m (48–72 in-lbs).
Oval air cleaner
  1. See Figure 3. Install cover and filter element.
    1. Install filter element (5).
    2. Install cover (4).
    3. Install screws (3). Tighten to 5.7–6.75 N·m (50–60 in-lbs).
  2. Install air cleaner trim insert.
    1. Install trim insert (2).
    2. Install trim insert screws (1). Tighten to 3–3.6 N·m (27–32 in-lbs).
1Cover screw
2Cover
3Seal
4Filter element
5Breather tube
6Filter screws (3)
Figure 1. Air Cleaner: Single Screw
1Cover screw (5)
2Cover
3Seal
4Filter element
5Breather tube
6Filter screws (3)
Figure 2. Air Cleaner: Five Screw
1Screw (2)
2Trim insert
3Screw (2)
4Cover
5Filter element
6Rain sock
Figure 3. Air Cleaner: Oval