Creating Code for the First Time
The personal code consists of five digits entered using the left and right turn signal switches. Each digit can be any number from 1-9. The personal code is intended to be used to disarm the vehicle in case the key fob is not functioning.
Record your personal code on the card(s) provided in the rear of the Owner's Manual. Carry one for reference in your wallet when riding.
To set a personal code on a motorcycle with no code previously installed, refer to Table 1. The procedure listed uses 3-1-3-1-3 as the sample personal code.
NOTE
For better security, do not use 3-1-3-1-3 as a personal code. It is shown as an example only.
Decide what five digit code the owner would like to use. The code will be programmed using the turn signal switches and key fob. Record your personal code on the card(s) provided in the rear of the Owner's Manual. Carry one for reference in your wallet when riding.
NOTE
The programming mode exits upon turning the key switch to OFF or if no turn signal switch/key fob button activity occurs for 60 seconds. No data is saved for partial configuration attempts of a first time entry.
Modifying Existing Codes
If a code was previously entered, the lamp will flash the equivalent digit. Each additional press of the left turn switch will increment the digit.
Table 1. Programming a Personal Code
STEP
NO.
ACTION
WAIT FOR CONFIRMATION
NOTES
NOTE: For better security, do not use 3-1-3-1-3 as a personal code. It is shown as an example only.
1
Set RUN/OFF switch to OFF
Verify that security lamp is not blinking (vehicle is disarmed)
2
Turn IGN key ON-OFF-ON-OFF-ON
3
Press left turn switch 2 times and release
1-3 flashes turn signals & indicators depending on vehicle configuration
(See BATTERY DISCONNECTS AND CONFIGURING section)
1 flash - Worldwide TSSM, no security
2 flashes - North American/Domestic configuration security system
3 flashes - international configuration security system
4
Quickly press key fob button 2 times and release
1 flash turn signals & indicators
Vehicle is in personal code entry mode
5
Press left turn switch 1 time and release
None if no code entered
1-9 flashes if code previously entered
A lack of confirmation flashes indicates no digit is entered
6
In this example, you will press and release three times
If code previously entered, count flashes for number and then press and release left turn switch to advance through the digits
Security lamp flashes to indicate each digit selected
Digit will display on odometer
In this example, the lamp will flash 3 times
You've selected 3 as a number for the first digit
7
Quickly press key fob button 2 times and release
2 flashes turn signals & indicators
You've confirmed 3 as a number for the first digit and have advanced to entering the second digit
8
Press left turn switch 1 time and release
None if no code entered
1-9 flashes if code previously entered
A lack of confirmation flashes indicates no digit is entered
9
In this example, you will perform this step one time
If code previously entered, count flashes for number and then press and release left turn switch to advance through the digits
Security lamp flashes to indicate each digit selected
Digit will display on odometer
In this example, the lamp will flash 1 time
You've selected 1 as a number for the second digit
10
Quickly press key fob button 2 times and release
3 flashes turn signals & indicators
You've confirmed 1 as a number for the second digit and have advanced to entering the third digit
11
Press left turn switch 1 time and release
None if no code entered
1-9 flashes if code previously entered
A lack of confirmation flashes indicates no digit is entered
12
In this example, you will repeat this step three times
If code previously entered, count flashes for number and then press and release left turn switch to advance through the digits
Security lamp flashes to indicate each digit selected
Digit will display on odometer
In this example, the lamp will flash 3 times
You've selected 3 as a number for the third digit
13
Quickly press key fob button 2 times and release
4 flashes turn signals & indicators
You've confirmed 3 as a number for the third digit and have advanced to entering the fourth digit
14
Press left turn switch 1 time and release
None if no code entered
1-9 flashes if code previously entered
A lack of confirmation flashes indicates no digit is entered
15
In this example, you will perform this step one time
If code previously entered, count flashes for number and then press and release left turn switch to advance through the digits
Security lamp flashes to indicate each digit selected
Digit will display on odometer
In this example, the lamp will flash 1 time
You've selected 1 as a number for the fourth digit
16
Quickly press key fob button 2 times and release
5 flashes turn signals & indicators
You've confirmed 1 as a number for the fourth digit and have advanced to entering the fifth digit
17
Press left turn switch 1 time and release
None if no code entered
1-9 flashes if code previously entered
A lack of confirmation flashes indicates no digit is entered
18
In this example, you will repeat this step three times
If code previously entered, count flashes for number and then press and release left turn switch to advance through the digits
Security lamp flashes to indicate each digit selected
Digit will display on odometer
In this example, the lamp will flash 3 times
You've selected 3 as a number for the fifth digit
19
Quickly press key fob button 2 times and release
1 flashes turn signals & indicators
You've confirmed 3 as a number for the fifth digit and have gone back to the first digit
20
Turn IGN key OFF
21
Write down code in owner's manual
22
Arm the security system and attempt to disarm using personal code entry