Arming
When the motorcycle is parked and the ignition key is turned to OFF, the Harley-Davidson Smart Security System arms automatically within five seconds if no motion is detected. Even when the fob is present, the system will arm.
On arming, the turn signals will flash twice and the optional siren will chirp twice. While armed, the key icon in the speedometer face will flash every three seconds.
NOTE
International Models: The HFSM must be in the Chirp Mode for the siren to chirp on arming or on disarming. See Hands-Free Security Module → Siren Chirp Mode (Confirmation).
Disarming
Once disarmed, the rider may ride or move the motorcycle for parking, storage or service without setting off the alarm.
Fob: An armed Smart Security System is automatically disarmed when the ignition key is turned to IGNITION with the fob present.
When the module disarms, the optional siren will chirp once and the key icon will illuminate for a solid four seconds and then turn off.
NOTE
Any motion, like lifting the motorcycle up off of its jiffy stand, or turning the ignition key to IGNITION and the module will electronically "poll" for the presence of the fob. If the fob is present, the system disarms.
Personal Identification Number (PIN): If the fob is misplaced or if the present fob fails to communicate with the module, the system can be disarmed with the Personal Identification Number (PIN).
Disarming with a PIN
Do not turn handlebars, straddle seat or lift motorcycle off the jiffy stand. During a PIN disarm, if the Smart Security System detects motorcycle motion the system will activate the alarm.
Table 1. Entering a PIN to Disarm Harley-Davidson Smart Security System
STEP
NO.
ACTION
WAIT FOR CONFIRMATION
NOTES
1
If necessary, verify the current 5-digit PIN.
Should be recorded on wallet card.
2
Turn ignition key to IGNITION.
3
Quickly (within 2 seconds of turning ignition key) hold both turn signal switches in until confirmation.
Key icon flashes at fast rate. In the odometer window, a flashing dash will be followed by four more dashes.
See figure showing the odometer window with PIN display. Five dashes will appear in the odometer window.
4
Enter first digit (a) in the PIN by pressing left turn switch a times.
The first digit (a) in the odometer will be the first digit in the PIN.
5
Press right turn switch 1 time.
The first digit is stored and the dash will flash.
Serves as enter key.
6
Enter second digit (b) in the PIN by pressing left turn switch b times.
The second digit (b) in the odometer will be the second digit in the PIN.
7
Press right turn switch 1 time.
The second digit is stored and the next dash will flash.
Serves as enter key.
8
Enter third digit (c) in the PIN by pressing left turn switch c times.
The third digit (c) in the odometer will be the third digit in the PIN.
9
Press right turn switch 1 time.
The third digit is stored and the next dash will flash.
Serves as enter key.
10
Enter fourth digit (d) in the PIN by pressing left turn switch d times.
The fourth digit (d) in the odometer will be the fourth digit in the PIN.
11
Press right turn switch 1 time.
The fourth digit is stored and the next dash will flash.
Serves as enter key.
12
Enter fifth digit (e) in the PIN by pressing left turn switch e times.
The fifth digit (e) in the odometer will be the fifth digit in the PIN.
13
Press right turn switch 1 time.
The fifth digit is stored. The key icon stops blinking.
Smart Security System is disarmed.
NOTE
  • At any time during a PIN disarm, if the fob is brought within range of the motorcycle, the Smart Security System will disarm when the module receives the coded signal from the fob.
  • If a mistake is made while entering PIN, wait two minutes before another disarming attempt.
  • The Smart Security System will remain disarmed until the ignition key is turned to OFF.
Arming with Hazard Warning 4-Way Flashers On
If it should be necessary to leave a motorcycle parked along side a roadway, the hazard warning four-way flashers can be turned ON and the Smart Security System armed.
  1. Turn ignition key to IGNITION.
  2. Simultaneously press both left and right turn signal switches to turn the four-way flashers ON.
  3. Turn the ignition key to OFF to arm the Smart Security System.
To turn hazard warning flashers OFF, turn the ignition key to IGNITION and simultaneously press the left and right turn signal switches.