Speedometer
WARNING
Travel at speeds appropriate for road and conditions and never travel faster than posted speed limit. Excessive speed can cause loss of vehicle control, which could result in death or serious injury. (00008a)
See Figure 1 and Figure 2. The speedometer registers miles per hour (U.S. models only) or kilometers per hour (international models only) of forward speed. The speedometer also provides the following selectable functions:
The speedometer has a single display window for the above functions.
  1. See Figure 1 and Figure 2. Pressing the function switch with the ignition switch in any position will activate the odometer reading and time. Time and mileage or kilometers may be checked without unlocking ignition switch. Press and release function switch once to view odometer. Press and release switch again to display time.
  2. To check mileage on trip odometers, the ignition switch must be in the ACC or IGNITION position. Press and release the function switch until the desired trip odometer reading is displayed. An A or B in the upper left of the display window identifies trip odometers.
  3. To reset or zero trip odometers, have desired (A or B) odometer in display window. Press function switch and hold switch for 2-3 seconds. The trip odometer will be reset to zero.
  4. Repeat the previous step if you wish to zero both trip odometers.
Setting Clock
  1. Turn the ignition switch to ACC or IGNITION.
  2. See Figure 1 and Figure 2. Press function switch until time (hour and minutes) is displayed. Press and hold the function switch for five seconds or until 12HR begins to blink in the speedometer display window. Release the button.
  3. Press and release the function switch once to advance to a blinking 24HR or military style time display. Each time you press and release the button, the display will switch between 12HR and 24HR.
  4. When the desired time style is displayed, press and hold the function switch for five seconds. The display will switch to the time display with the hours blinking.
    5. NOTE
    There is no AM or PM time setting required. So when correct hour is reached, press and hold function switch to advance to minute setting.
  5. Press and release the function switch repeatedly to advance the hours. Each time you press and release the switch, the display will advance one hour.
  6. When the correct hour is displayed, press and hold the function switch for five seconds. The minutes display will start blinking.
  7. Press and release the function switch repeatedly to advance the minutes display. Each time you press and release the button, the display will advance one minute.
  8. When the correct minutes are displayed, press and hold the function switch for five seconds. The minutes display will stop blinking, indicating that the clock has been set.
  9. Turn the ignition switch OFF.
Tip Indicator
WARNING
If tip occurs, check all controls for proper operation. Restricted control movement can adversely affect the performance of the brakes, clutch or ability to shift, which could result in loss of vehicle control and death or serious injury. (00350a)
Should motorcycle be tipped over, the word "tip" will appear in the odometer window. Engine will not start until reset. To reset, cycle ignition/headlamp key switch ON-OFF-ON.
Fuel Range Function
The fuel range function shows the approximate mileage available with the amount of fuel left in the fuel tank.
  1. With the ignition switch in the ACC or IGNITION position, press function switch until fuel range function is displayed, as indicated by the letter 'r' in the left side of the odometer display. The calculated remaining distance (miles or kilometers) to empty is displayed, based on the amount of fuel in tank. Range can be accessed at any time using the function switch.
  2. When the low fuel warning lamp illuminates, the range feature will automatically be displayed in the odometer unless this automatic pop-up feature is disabled by a press and hold of the function switch while in range display mode. Automatic range pop-up feature will show that it is disabled by blinking twice. Likewise, automatic range popup can be reactivated by a press and hold of the function switch. Range will blink once when the automatic pop-up feature is re-enabled.
    3. NOTE
    • When the low fuel warning lamp turns on, there is approximately 3.79 L (1.00 USgal) of fuel remaining in the tank. Refuel as soon as possible.
    • The range display is only updated when the vehicle is moving.
  3. After the range calculation reaches 16 km (10 mi) remaining, the range display will display "r Lo" to indicate that the vehicle will shortly run out of fuel.
  4. Resetting the low fuel warning lamp and range requires an ignition cycle change.
1Speedometer
2Tripodometer/Odometer
3Function switch
4Security system lamp
5Fuel gauge
6Sixth gear lamp
7Check engine lamp
8Low fuel warning lamp
9Battery lamp
Figure 1. Speedometer/Odometer: Softail Models (typical)
1Speedometer (domestic shown)
2Indicator lamps
3Function switch
4Fuel gauge
Figure 2. Instruments: FLSTC, FLSTSB Models