Service Lamps
See Operation → Instruments → Instrument Module Displays and Selections. The service lamps indicate the condition of the powertrain/powertrain management system.
EV Alert: Amber Icon appears when the vehicle has detected the vehicle requires maintenance and/or repair but can still be operated.
EV Fault: Red Icon appears when the vehicle has detected an error, the vehicle should not be operated and will go into shutdown mode.
Malfunction Indicator Lamp (MIL): The Malfunction Indicator Lamp (MIL) normally comes on when the ignition is first turned on. During this time, the powertrain management system runs a series of self-diagnostics.
If the MIL does not turn off after enabling propulsion or comes on at any other time, See an authorized LiveWire dealer.
Side Bar Lamps
Charging: When charging, the sidebar lamps illuminate in a red, yellow, green succession.
Accessory mode: The side bar lamps are blue when the motorcycle is in accessory mode.
Propulsion not enabled: With the OFF/RUN switch in the RUN position the sidebar lights are yellow when propulsion is not enabled.
Propulsion enabled: With the OFF/RUN switch in the RUN position the sidebar lights are green when propulsion is enabled.
Propulsion Enabled
See Operation → Instruments → Instrument Module Displays and Selections. The Propulsion enabled Indicator replaces the settings icon on the Instrument Module (IM) when propulsion has been enabled.
Bluetooth
See Operation → Instruments → Instrument Module Displays and Selections. The bluetooth indicator displays the connection status of the IM. When connected to a device the indicator will be blue, when no connection is detected the indicator will be grey.
Propulsion Limited
See Operation → Instruments → Instrument Module Displays and Selections. The Propulsion limited Indicator illuminates when there is a fault that requires performance to be limited.
12 V Battery Discharge
See Operation → Instruments → Instrument Module Displays and Selections. The battery discharge lamp indicates overcharging or undercharging of the 12 V battery.
Coolant Temperature
WARNINGDo not loosen or remove pressure cap when cooling system is hot. The cooling system is under pressure and hot coolant and steam can escape from pressure cap, which could cause severe burns. Allow motorcycle to cool before servicing the cooling system. (00091c)
See Operation → Instruments → Instrument Module Displays and Selections. The coolant temperature Indicator illuminates when the coolant has exceeded threshold temperature.
If coolant level is sufficient and the lamp remains on, see a LiveWire dealer for service.
Ride Mode
See Operation → Instruments → Instrument Module Displays and Selections. The ride mode Indicator displays the current selected ride mode. See Operation → Widgets.
Security/Fault Lamp
See Operation → Instruments → Instrument Module Displays and Selections. The security lamp displays the status of the security system and electrical self-diagnostics for the motorcycle. Refer to SECURITY SYSTEM for security system operation.
Flashing: The security system is armed.
Solid (security system armed): The alarm has been activated.
Solid (security system disarmed): If the lamp remains on after the security system has been disarmed, see a LiveWire dealer.
Turn Signal Indicator Lamps
Flashing: A turn signal is activated. When the 4-way hazard flashers are operating, both turn indicators flash simultaneously.
Rapid flashing: A turn signal bulb is not operating. Exercise caution and use hand signals. Replace inoperative components at earliest opportunity.
Headlamp High Beam Lamp
See Operation → Instruments → Instrument Module Displays and Selections. The headlamp high beam lamp is on when the high beam or flash to pass switch is activated.
Cruise Control
Off: Cruise control is not enabled.
Enabled - speed not set: Cruise control is enabled, cruising speed is not set. Cruise indicator shown in amber color without speed setting.
Enabled - speed set: Cruising speed is set. Motorcycle speed is maintained by the cruise control system. Cruise indicator and speed setting shown in green color.
Enabled - speed set disengaged: Cruising speed is set but has been disengaged. Motorcycle speed is not maintained by the cruise control system. Cruise indicator and speed setting is shown in red color.
ABS Lamp
WARNINGIf ABS lamp continues flashing at speeds greater than 5 km/h (3 mph) or remains on continuously, the ABS is not operating. The standard brake system is operational, but wheel lock up can occur. Contact a LiveWire Dealer to have ABS repaired. A locked wheel will skid and can cause loss of vehicle control, which could result in death or serious injury. (12135b)
Flashing: The ABS lamp begins flashing when the vehicle is turned on. The flashing lamp indicates that the system is in self-diagnosis mode. It continues to flash until motorcycle speed exceeds 5 km/h (3 mph). ABS is not operational until the lamp turns off.
Solid: Continuous illumination of the lamp indicates an ABS malfunction. The ABS is disabled and the brakes are operating as if they were non-ABS brakes. See a LiveWire dealer for service.
Traction Control Lamp
Solid: Traction control has been turned off.
Flashing: Traction control system active intervention.
Off: Traction control system is on.
Solid with Security/Fault indication lamp On: Continuous illumination of the lamp with the Security/Fault indication lamp indicates a traction control fault. Traction control is disabled and the motorcycle is operating as traction control turned off. See a LiveWire dealer for service.