Checking Headlamp Alignment
  1. Adjust tire pressure to recommended pressure. Refer to Specifications → Specifications → Tires and Tire Pressure.
  2. Adjust rear shocks for the rider and intended load. See Before Riding.
  3. Fill fuel tank or add an equal amount of ballast.
    4. NOTE
    Choose a wall in minimum light.
  4. See Figure 1. Park the motorcycle in a line (1) perpendicular to the wall.
  5. Position motorcycle so that front axle is 7.6 m (25 ft) from wall.
  6. Draw a vertical line (2) on the wall.
  7. Point the front wheel straight forward at the wall.
  8. Measure the distance (4) from the floor to the center of the high beam bulb.
  9. Activate high beam and verify headlamp alignment.
  10. Adjust if necessary.
1Perpendicular line
2Vertical line
37.6 m (25 ft)
4High beam bulb centerline
5Horizontal line 53.3 mm (2.1 in) lower than bulb centerline
Figure 1. Checking Headlamp Alignment
Adjusting Headlamp
Set Horizontal Adjustment
1. See Figure 2. Remove speed screen screws (1) and washers (2).
2. Pull speed screen away from upper speed screen bracket (4).
3. Pull speed screen way from lower speed screen bracket (5) to remove posts (6) from grommets.
4. See Figure 3. Loosen horizontal adjustment locknut (1).
5. Direct light beam straight ahead.
6. Tighten horizontal adjustment locknut to 34–41 N·m (25–30 ft-lbs).
NOTE
Perform all adjustments before installing speed screen.
7. See Figure 2. Align posts of speed screen (3) with grommets.
8. Install speed screen onto lower speed screen bracket (5).
9. Align speed screen to upper speed screen bracket (4).
10. Install washers (2) and screws (1). Tighten to 2.3–3.3 N·m (21–29 in-lbs).
Set Vertical Adjustment
1. Loosen locknut (1) for vertical adjustment bolt (2)
2. Aim headlamp at horizontal line on wall.
3. Tighten vertical adjustment locknut to 21–26 N·m (15–19 ft-lbs).
1Screw (2)
2Washer (2)
3Speed screen
4Upper speed screen bracket
5Lower speed screen bracket
6Post (2)
Figure 2. Headlamp Speed Screen
1Vertical adjustment locknut
2Vertical adjustment bolt
3Horizontal adjustment locknut
Figure 3. Headlamp Adjustment
Replacing Headlamp or Position Bulb
WARNING
The automatic-on headlamp feature provides increased visibility of the rider to other motorists. Be sure headlamp is on at all times. Poor visibility of rider to other motorists can result in death or serious injury. (00030b)
1. See Figure 2. Remove screws (1) and washers (2).
2. Pull speed screen away from upper speed screen bracket (4).
3. Pull speed screen way from lower speed screen bracket (5) to remove posts (6) from grommets.
4. Remove main fuse. See Service Procedures → Fuses and Relays.
5. See Figure 4. Remove screws (6).
6. Pull lens assembly (5) from headlamp housing.
7. Disconnect electrical connectors from headlamp and position bulbs.
8. Loosen screw (2).
9. Remove retainer (3).
10. Remove headlamp bulb (4).
11. Remove position bulb (7).
12. Install new headlamp or position bulb.
13. Install retainer (3).
14. Tighten screw (2).
15. Connect electrical connectors to headlamp and position bulbs.
16. Attach lens assembly (5) to headlamp housing.
17. Install screws (6).
18. See Figure 2. Align posts of speed screen (3) with grommets.
19. Install speed screen onto lower speed screen bracket (5).
20. Align speed screen to upper speed screen bracket (4).
21. Install washers (2) and screws (1). Tighten to 2.3–3.3 N·m (21–29 in-lbs).
22. Install main fuse. See Service Procedures → Fuses and Relays.
WARNING
Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a)
23. Test lamp operation.
1Boot
2Screw
3Retainer
4Headlamp bulb
5Lens assembly
6Screw (2)
7Position bulb
Figure 4. Headlamp Bulb