Hazard Warning 4-Way Flasher

See Figure 1. The hazard warning switch (2) is used to leave a stranded motorcycle in the 4-way flashing mode. With the flashers, the motorcycle can be left with the ignition off until assistance is found. Refer to Table 1.

With the OFF/RUN/START switch in the RUN (3) position, press the hazard warning switch to activate the 4-way flashers.

NOTE

The fob must be present when turning on the 4-way flashers and when canceling the flashers.
The four-way flashers will operate when the vehicle is tipped over regardless of OFF/RUN/START switch position. See Operation → Starting after Tipover.

Turn OFF/RUN/START switch to OFF (4). The 4-way flashers continue for 2 hours or until cancelled by the rider.
To cancel, turn the OFF/RUN/START switch to RUN. Press the hazard warning switch.

OFF

See Figure 1. Press the engine OFF/RUN/START switch to OFF (4) to shut off the engine. Refer to Table 1.

RUN

See Figure 1. Push the engine OFF/RUN/START switch to RUN (3) to enable engine start and run. The engine OFF/RUN/START switch must be in the RUN position to start or operate the engine. Refer to Table 1.

Right Turn Signal

Activate:

See Figure 1. Press the right turn signal switch (9) to activate the right turn signal. Refer to Table 1.

Cancel (manual operation): If activated, press the right turn signal switch to cancel the right turn signal.

Cancel (automatic operation): The turn signal lamps automatically cancel when a full turn has been detected based on speed, acceleration and turn completion.

The lamps also cancel if the turn signal has been activated for a prolonged period (20 flashes) while the motorcycle speed is greater than 11 km/h (7 mph). If the motorcycle is stopped or moving slower than this speed, the turn signal continues flashing.

NOTE

Front turn signal lamps also function as running lamps. This feature may not be available in all markets.

Volume Up

See Figure 1. Press the volume up (1) button to increase volume. Refer to Table 1.

See Figure 1. Press the next button (7) to select the next media file. Refer to Table 1.

Volume Down

See Figure 1. Press the volume down (11) button to decrease volume. Refer to Table 1.

See Figure 1. Press the previous button (12) to select the previous media file. Refer to Table 1.

Play/Pause

See Figure 1. Press the play/pause button (13) to play or pause the current media file. Refer to Table 1.

Push-to-Talk

See Figure 1. The Push-To-Talk (PTT) switch (6) is used to operate the rider/passenger intercom on equipped vehicles. Refer to Table 1.

Start

See Figure 1. Switch the OFF/RUN/START switch to RUN (3). Shift the transmission to neutral. The neutral (green) indicator illuminates. See Operation → Starting the Engine.
Press the OFF/RUN/START switch to START (5) to operate the starter motor. Refer to Table 1.

NOTE

When the starter is activated, the headlamp is momentarily turned off to reduce battery load.
If the engine does not start, the starter motor runs for ten seconds and stops. Release the start switch. Press the start switch to try again. After several unsuccessful attempts to start the engine, see a Harley-Davidson dealer.

Voice Recognition

See Figure 1. The voice recognition switch (8) activates the voice recognition features on a connected mobile device. Refer to Table 1.

Using natural language processing allows a larger range of phrase requests that are more natural to each user.

Mode

See Figure 1. Press the mode button (10) to change the ride mode. See Operation → Ride Modes. Refer to Table 1.

NOTE

Last active mode is automatically enabled at each ignition start cycle and when enabled.

1	Volume up
2	Hazard warning
3	Run
4	Off
5	Start
6	Push-To-Talk
7	Next
8	Voice recognition
9	Right turn signal
10	Mode
11	Volume down
12	Previous
13	Play/pause

Figure 1. Right Hand Control Module (RHCM)

Table 1. Right Hand Control Switches

SWITCH	NAME	FUNCTION
	Hazard	Press to activate the 4-way flashers.
	Run	Press to allow the engine to start and run.
	Start	Press to start the engine.
	Off	Press to stop the engine or to prevent the engine from starting.
	Push-To-Talk	Press and hold to activate talk function.
	Voice recognition	Initiates a voice recognition session.
	Volume up	Press to increase volume.
	Volume down	Press to decrease volume.
	Next	Press to select the next media file.
	Previous	Press to select the previous media file.
	Play/pause	Press to play or pause the current media file.
	Mode	Press to change the ride mode.