Special Tools

Description	Part Number	Qty.
SHOCK ADJUSTMENT SPANNER	94448-82B	1

Calculate Number of Preload Turns

The rear shock spring preload is pre-set to the total load. It can be varied to suit your own personal comfort.

NOTE

To determine the motorcycle configuration for an FLS or FLSTFB, check the configuration/calibration character stamped on the VIN. Refer to Identification → Vehicle Identification Number (VIN) → Harley-Davidson VIN Breakdown: 2016 Softail Models.

Identify the number of preload turns for the weight of the rider.
1. FLSTC, FLSTF, FLS (APC, AUS), FLSTFB (HDI, ENG, IND, BRZ): Refer to Table 1.
2. FXSB, FLSTN, FLS (all except APC/AUS), FLSTFB (all except HDI, ENG, IND, BRZ): Refer to Table 2.
Calculate the number of turns for the intended passenger and cargo.
Add the number of turns for the rider to the number of turns required for the total weight of the passenger and/or cargo.

Table 1. Shock Preload: FLSTC, FLSTF, FLS (APC, AUS), FLSS (AUS), FLSTFB (HDI, ENG, IND, BRZ), FLSTFBS (HDI, ENG)

RIDER WEIGHT*	TURNS**
Less than 75 kg (165 lb)	0
75–100 kg (165–220 lb)	1
100–125 kg (220–275 lb)	2
125–152 kg (275–335 lb)	3
152–179 kg (335–395 lb)	4
179 kg (395 lb) to maximum added weight allowed (refer to Specifications → Specifications → Weights: FLSTC, FLSTF, FLSTFB, FLSTFBS and FLSTN and Specifications → Specifications → Weights: FLS, FLSS and FXSB )	5
* Passenger/Cargo: For every 18.1 kg (40 lb) increase preload one turn. ** Turns out (counterclockwise) from minimum preload.

Table 2. Shock Preload: FXSB, FLSTN, FLS (all except APC, AUS), FLSS (all except AUS), FLSTFB (all except HDI, ENG, IND, BRZ), FLSTFBS (all except (HDI, ENG)

RIDER WEIGHT*	TURNS**
Less than 84 kg (185 lb)	0
84–107 kg (185–235 lb)	1
107–129 kg (235–285 lb)	2
129–154 kg (285–340 lb)	3
154 kg (340 lb) to maximum added weight allowed (refer to Specifications → Specifications → Weights: FLSTC, FLSTF, FLSTFB, FLSTFBS and FLSTN and Specifications → Specifications → Weights: FLS, FLSS and FXSB)	4
* Passenger/Cargo: For every 15.8 kg (35 lb) increase preload one turn. ** Turns out (counterclockwise) from minimum preload.

Adjustment

NOTE

Adjust the shocks with the motorcycle resting on the jiffy stand.
Adjust both shocks the same number of turns.

See Figure 1. Hold the shaft with a wrench on the flats of the shock shaft (3) and loosen the jamnut (1).
Use the tangs of the SHOCK ADJUSTMENT SPANNER (Part Number:94448-82B) (4) in the holes (2) in the rear shock canister to turn the canister clockwise until it stops. This position is the minimum rider weight position.
Mark the face of the canister for reference.
Turn the canister counterclockwise the number of turns calculated for the total load.
Tighten the jamnut.

1	Jamnut
2	Holes for spanner
3	Flat
4	Spanner wrench

Figure 1. Shock Absorber Adjustment