WARNING
Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a)
WARNING
Do not operate motorcycle without saddlebags attached because they contain side and/or rear reflectors. Motorcycle operation without reflectors can violate local regulations and lead to decreased visibility of the motorcycle to other motorists, which could result in death or serious injury. (12904a)
NOTE
Maximum saddlebag weight capacity is 6.8 kg (15 lb) in each saddlebag.
Saddlebag Speakers
The saddlebags and speakers are designed to prevent water intrusion and to allow water to drain during washing or riding in all weather. To remove any standing water from the speakers, open the saddlebags and gently shake any remaining water from the speakers.
Locking
Key:See Figure 1. Insert key. Rotate key one-quarter turn toward front of vehicle. Return key to center to remove key.
Key fob:Refer to Operation → Power Locks → Key Fob. Press the LOCK button on the key fob. The turn signals flash twice to indicate the saddlebags are locked.
Bike function menu:Refer to Operation → Left Hand Control Switches → Left Hand Control Module (LHCM).Long press menu/Bike function button to access power lock function in the IFCU.
Unlocking
Key:See Figure 1. Insert key. Rotate key one-quarter turn toward rear of vehicle. Return key to center to remove key.
Key fob:Refer to Operation → Power Locks → Key Fob. Press the UNLOCK button on the key fob. The turn signals flash once to indicate the saddlebags are unlocked.
Bike function menu:Refer to Operation → Left Hand Control Switches → Left Hand Control Module (LHCM).Long press menu/Bike function button to access power lock function in the IFCU.
Opening
  1. See Figure 1. Unlock saddlebag.
  2. Lift the saddlebag lever (3).
  3. Lift the lid from the inner side of the saddlebag.
Closing
  1. See Figure 1. Close the saddlebag lid.
  2. Push the lever (3) down to engage the latches. Check that the lid is secure.
  3. Lock the saddlebag.
Remove
  1. See Figure 1. Open the saddlebag.
  2. See Figure 2. Turn the mounting screw levers (1) counterclockwise to remove the mounting screws from the support bracket.
  3. Support the saddlebag and disconnect the audio connector (3).
    1. See Figure 3. Press the release tab. Separate the connector halves.
  4. Lift the saddlebag from the saddlebag rail.
NOTE
Do not drag or scrape saddlebags on the ground. Improper care can damage the saddlebags.
Install
  1. See Figure 2. Carefully place saddlebag in position on saddlebag rail (4). Align the mounting grommets with the support bracket (2).
  2. Support the saddlebag. Connect the audio connector (3).
    1. See Figure 3. Press the connector halves together until the release tab clicks.
    3. NOTE
    The rear mounting screw lever will interfere with the saddlebag cover unless positioned with lever pointed downward.
  3. See Figure 2. Install the mounting screws (1) through the grommets into support bracket (2). Turning the levers clockwise, tighten the mounting screws so the levers are pointed downward between the 3 o'clock and 9 o'clock positions as shown.
  4. Check that the saddlebag is secure.
  5. Close and lock the saddlebag.
1Unlock position (toward rear)
2Lock position (toward front)
3Lever
4Saddlebag lock
Figure 1. Saddlebag
1Mounting screw with lever (2)
2Support bracket
3Connector
4Saddlebag rail
Figure 2. Saddlebag Removal/Installation
Figure 3. Right Side Harness Connector Release Tab (Left Side Same)