Arming
When the motorcycle is parked and the ignition is turned to OFF or ACCESSORY, the security system arms automatically within five seconds if no motion is detected. Even when the fob is present, the system arms.
On arming, the turn signals flash twice and the optional siren chirps twice if the siren is in the chirp mode. While armed, the indicator lamp in the speedometer face flashes every three seconds.
NOTE
Models with optional siren: The system must be in the chirp mode for the siren to chirp on arming or disarming. See SECURITY SYSTEM → Siren Chirp Mode (Confirmation).
Disarming
With the fob present, the rider may ride or move the motorcycle for parking, storage or service without setting off the alarm. Disarming is automatic as long as the fob is within range.
Fob: An armed security system is automatically disarmed when the fob is present and the motorcycle is moved or the ignition switch is turned to IGNITION or ACCESSORY. The range of the fob is 2 m (5 ft).
When the system disarms, the optional siren chirps once and the security indicator lamp illuminates for a solid four seconds and then turns off.
Personal identification number (PIN): If the fob is misplaced or if the present fob fails to communicate, the system can be disarmed with the personal identification number (PIN). Refer to Table 1.
Disarming with a PIN
Disarm the security system manually using the PIN if the fob is lost, the fob battery is discharged or if where you parked there is a strong electromagnetic interference.
Do not turn handlebars, straddle seat or lift motorcycle off the jiffy stand. During a PIN disarm, if the security system detects motorcycle motion the system will activate the alarm.
NOTE
  • If a mistake is made while entering PIN, turn the ignition switch to OFF before entering the last digit and then start the procedure from the beginning.
  • If the procedure fails to disarm the security system, wait two minutes before attempting another PIN disarm.
  • The security system remains disarmed until the ignition is turned to OFF.
  • At any time during a PIN disarm if the fob is brought within range, the security system disarms as the module receives the coded signal from the fob.
Table 1. Entering a PIN to Disarm Security System
STEP
NO.
ACTION
WAIT FOR CONFIRMATION
NOTES
1
If necessary, verify the current 5-digit PIN.
Should be recorded.
2
Turn ignition to IGN.
If armed, the odometer window display will read: ENTER PIN and the security lamp will be flashing at a fast rate. The headlight will not be on.
3
Press and release the left turn signal switch.
In the odometer window, a flashing 1 will appear.
4
Advance the digit by tapping the left turn signal until the odometer window displays the first digit of the PIN.
The first digit in the odometer will be the first digit in the PIN.
5
Press right turn switch 1 time.
The first digit is stored and the next digit will flash.
Serves as enter key.
6
Advance the second digit using the left turn switch until the digit reaches the second digit of the PIN.
The second digit in the odometer will be the second digit in the PIN.
7
Press right turn switch 1 time.
The second digit is stored and the next dash will flash.
Serves as enter key.
8
Advance the third digit using the left turn switch until it reaches the third digit of the PIN.
The third digit in the odometer will be the third digit in the PIN.
9
Press right turn switch 1 time.
The third digit is stored and the next dash will flash.
Serves as enter key.
10
Advance the fourth digit using the left turn switch until it reaches the fourth digit of the PIN.
The fourth digit in the odometer will be the fourth digit in the PIN.
11
Press right turn switch 1 time.
The fourth digit is stored and the next dash will flash.
Serves as enter key.
12
Advance the fifth digit using the left turn switch until it reaches the fifth digit of the PIN.
The fifth digit in the odometer will be the fifth digit in the PIN.
13
Press right turn switch 1 time.
The fifth digit is stored. The security system indicator lamp stops blinking.
Security System is disarmed.