The transmission lubricant level should be checked monthly.
Refer to Maintenance Scheduling → Regular Service Intervals: Buell Models → Regular Service Intervals: 2007 XB Models. The transmission should be drained and refilled with fresh lubricant at proper intervals. For best results, drain lubricant while hot.
NOTE
When checking the transmission lubricant level, motorcycle should be standing STRAIGHT UP, not leaning on the side stand. Keep motorcycle upright for a short period of time to equalize lubricant level in the transmission compartments.
Check Lubricant Level
1. Ride motorcycle until engine is warmed up to normal operating temperature.
2. Position motorcycle straight up.
3. See Figure 1. Remove screws with washers from clutch inspection cover (1). Remove clutch inspection cover from primary cover.
NOTE
The filler access is the clutch inspection cover.
NOTICE
When draining or adding lubricant, do not allow dirt, debris or other contaminants to enter the engine. (00198a)
WARNING
Be sure that no lubricants or fluids get on tires, wheels or brakes when changing fluid. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury. (00047d)
NOTICE
Do not overfill the primary chaincase with lubricant. Overfilling can cause rough clutch engagement, incomplete disengagement, clutch drag and/or difficulty in finding neutral at engine idle. (00199b)
4. See Figure 2. Verify that lubricant level is even with bottom of clutch diaphragm spring.
NOTE
Add only enough of GENUINE Harley-Davidson FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT (Part No. 98851 quart) through clutch inspection cover opening until the lubricant reaches the bottom of clutch diaphragm spring.
5. Install clutch inspection cover on primary cover using screws with washers removed in step 3. Tighten screws in a crosswise pattern to 9.5–12.2 N·m (84–108 in-lbs).
6. Start engine. Check for any lubricant leaks.
7. Turn engine off.
1Inspection cover
2Primary drain plug
Figure 1. Primary Drain Plug: Ulysses XB12X
Changing Lubricant
1. Ride motorcycle until engine is warmed up to normal operating temperature.
2. When the engine reaches normal operating temperature, turn the engine off and position motorcycle on side stand. This will allow the chaincase lubricant to drain out of transmission.
3. See Figure 1. Position a suitable container under primary drain plug (2).
NOTE
The drain plug is located under the clutch, on the underside of the chaincase.
4. Remove drain plug and drain lubricant.
5. Position the motorcycle STRAIGHT UP and LEVEL. This allows additional fluid to be drained from clutch compartment.
NOTE
Dispose of transmission lubricant in accordance with local regulations.
6. Remove foreign material from magnetic drain plug. Apply LOCTITE 565 PST THREAD SEALANT (Part No. 99818-97) and install drain plug and tighten to 19–41 N·m (14–30 ft-lbs).
NOTICE
Do not over-tighten filler or drain plug. Doing so could result in a lubricant leak. (00200b)
NOTICE
When draining or adding lubricant, do not allow dirt, debris or other contaminants to enter the engine. (00198a)
WARNING
Be sure that no lubricants or fluids get on tires, wheels or brakes when changing fluid. Traction can be adversely affected, which could result in loss of control of the motorcycle and death or serious injury. (00047d)
NOTICE
Do not overfill the primary chaincase with lubricant. Overfilling can cause rough clutch engagement, incomplete disengagement, clutch drag and/or difficulty in finding neutral at engine idle. (00199b)
7. See Figure 1. Remove screws with washers from clutch inspection cover (1). Remove clutch inspection cover from primary cover.
NOTE
The filler access is the clutch inspection cover.
8. See Figure 2. Add 32 fluid ounces (0.95 liters) of GENUINE Harley-Davidson FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT (Part No. 98851) through the clutch inspection cover opening or until the lubricant reaches the bottom of clutch diaphragm spring (1).
9. Install a new clutch inspection cover gasket.
10. Install clutch inspection cover on primary cover using screws with washers removed. Tighten screws in a crosswise pattern to 9.5–12.2 N·m (84–108 in-lbs).
11. Start engine. Check for any lubricant leaks.
12. Turn engine off.
Figure 2. Primary Fluid Level: XB Models