Settings Menu

WARNING

Set volume levels and other controls on audio and electronic devices before riding. Distractions can lead to loss of control, resulting in death or serious injury. (00088b)

See Operation → Indicators → Menu Selections. Selecting the bike status card (1) displays the menus used to set up ride modes, appearance, system, icons and user settings.

NOTE

To make full use of features and minimize distraction while on the road, configure the system with your personal preferences before riding.

After propulsion has been enabled the settings menu is disabled.

Table 1. Settings Main Menu

Press	Result
[Settings]	Configure instrument module settings. Do before riding the motorcycle.
[Settings]	Available selections: General, Ride Customization, Appearance, Bluetooth, Phone Notifications, Software.

GENERAL

Table 2. Settings Menu: General

Press	Result
[General]	Configure instrument module settings. Do before riding the motorcycle.
[General]	Available selections: Trip Reset, Adjust Date, LW App Time Sync, Adjust Clock Time, Clock Format, Units, Change Security Pin, Display Language.
	Trip Reset	Select from Trip A or B, Reset Trip
	Adjust Date	Manually set date displayed
	LW App Time Sync	Toggle On/Off
	Adjust Clock Time	Manually set time displayed
	Clock Format	Select 12 or 24 hour time display
	Units	Select Standard or Metric units of measure
	Change Security Pin	Select PIN for security system
	Display Language	Select language to display
	Target Charge Percent	Select target charge percent of 80%, 90% or 100%

RIDE CUSTOMIZATION

Table 3. Settings Menu: Ride Customization

Press	Result
[Ride Customization]	Allows enable and disable of available ride modes and allows setup of custom ride modes.
	Preset ride mode selections: Preset Ride mode selections: Enable/Disable, Copy+Edit.⁽¹⁾
	Custom ride mode selections: Enable/Disable, Power slider, Regen slider, Throttle slider, Traction control setting⁽²^{, 3)}

(1) Copy+Edit selection will copy the selected ride mode into a selected custom ride mode option and allow the rider to build a custom ride mode using a preset selection as a starting point.

(2) Power Slider adjusts how much overall power will be available in the custom ride mode. Regen slider adjusts how much regen will be enabled in the custom ride mode. Throttle slider adjusts the intensity of throttle response felt by the rider in the custom ride mode.

(3) The traction control level adjusts how much rear wheel slip the system will allow. Traction control adjustment does not affect the performance of drag torque slip control or ABS functions.

APPEARANCE

Table 4. Settings Menu: Appearance

Press	Result
[Appearance]	Configure instrument module appearance.
[Appearance]	Available selections: Auto-Brightness (on/off), Brightness Level (adjustable slider).

BLUETOOTH

Table 5. Settings Menu: Bluetooth

Press	Result
[Bluetooth]	Configure connections with bluetooth devices.
[Bluetooth]	Available selections: Phone List, Add New Phone, Headset List, Add New Headset
	Phone List	Shows paired phones
	Add New Phone	Use to pair new phone to vehicle
	Headset List	Shows paired headsets
	Add New Headset	Use to pair new headset to vehicle

PHONE NOTIFICATIONS

Table 6. Settings Menu: Phone Notifications

Press	Result
[Phone Notifications]	Configure which phone notifications are displayed.
[Phone Notifications]	Available selections: Call notifications (on/off) and text notifications (on/off).

SOFTWARE

Table 7. Settings Menu: Software

Press	Result
[Software]	View and update software versions.
[Software]	Available selections: Infotainment SW Update, Regulatory Info, Software Information
	Infotainment SW Update	Displays available updates
	Regulatory Info	Displays regional regulatory information
	Software Information	Displays software part number/revision, hardware part number/revision and hardware serial number

Updating Software

1.	Check software version. a. Refer to Table 7. Settings> Software> Software Information. This menu will show the current software version on the Instrument Module (IM). b. Check for latest software version. See website: www.H-D.com/infotainment-support.
2.	Update software. a. Download the latest software version to Universal Serial Bus Type-C (USB-C) device. See website: www.H-D.com/infotainment-support. b. Unzip the downloaded file to extract the pv2 file. The pv2 file must be at the root directory of your USB-C drive in order for it to be detected by the IM. Only one pv2 file should be present at the root directory level. c. See Your Motorcycle → Primary Controls and Service Components → Controls and Service Components (Typical). Connect USB-C drive to motorcycle. d. Refer to Table 7. Settings> Software> Infotainment SW Update. e. Select software update file. f. Select check mark to start update. g. Allow update to complete. h. Remove USB-C drive.

USER SETTINGS

Charge State/Range

NOTE

Actual range will vary depending on riding habits, ambient weather and equipment conditions.

See Figure 1. The charge state and range bar displays the charge state of the Rechargeable Energy Storage System (RESS) and estimated remaining range.

Speedometer

WARNING

Travel at speeds appropriate for road and conditions and never travel faster than posted speed limit. Excessive speed can cause loss of vehicle control, which could result in death or serious injury. (00008a)

See Figure 1. The IM registers miles per hour (MPH) (U.S. models default) and kilometers per hour (km/h) (international models default). The IM can be configured to register either miles per hour or kilometers per hour through the settings menu.

Instrument backlighting changes with ambient lighting differences, changes in ambient light, such as such as going through a tunnel, may change level of backlighting.

Clock

See Figure 1. The clock displays current time in 12/24 hour format. The settings menu is used to set time and select 12 hours or 24 hours format.

Odometer

Pressing the trip switch with the OFF/RUN switch in either position activates the odometer reading.

See Operation → Left Hand Control Switches → Left Hand Control Module and Operation → Instrument Alerts → Trip Screen. The odometer display also provides the following selectable displays:

Odometer
Trip odometer A
Trip odometer B
Ambient temperature

Press and release the trip switch to cycle through the displays.

Trip Odometers A and B

See Operation → Left Hand Control Switches → Left Hand Control Module and Operation → Instrument Alerts → Trip Screen. To check mileage or to reset trip odometers, the OFF/RUN switch must be in the RUN position. Press and release the trip switch until the desired trip odometer is displayed. An A or B on the left of the odometer display identifies the trip odometer.

To reset or zero trip odometers, have desired (A or B) odometer displayed. Press the trip switch and hold for approximately 1 second. The trip odometer resets to zero.

Propulsion Interlocks

See Figure 1. The vehicle is equipped with propulsion interlocks. Propulsion interlocks are conditions that must be met before propulsion can be enabled. Propulsion interlock messages will be displayed on the IM when conditions are not met to enable propulsion.

Propulsion interlock messages include; CALL SERVICE, UNPLUG TO RIDE, PRESS RUN, WAIT - NOT READY, UNLOCK FORK, RAISE SIDE STAND, RELEASE TWIST GRIP and PRESS START.

1	Charge state/Range bar
2	Left turn signal
3	Right turn signal
4	Speedometer
5	Headset connection
6	Bluetooth
7	Device signal
8	Device battery
9	12V battery discharge
10	MIL/OBD fault
11	Low state of charge
12	Headlamp high beam
13	Low tire pressure
14	Maintenance required
15	Rear Anti-lock Braking System (ABS) disabled
16	ABS
17	Traction control
18	Coolant temperature
19	EV alert
20	Clock
21	Ride mode

Figure 1. Instrument Module Displays and Selections